Table of Contents
To reset the light strip, locate the corded controller which is attached to the power supply of the light strip. Insert a paper clip, or a similar sized object, into the reset hole on the controller (depicted below). Using the paper clip, press and hold the reset button inside the reset hole for eight (8) seconds.
How do I reset my Smart Strip light?
Press and hold the light switch controller for 10 seconds or more and then release. The light strip animating orange and green after that indicates a successful factory reset. Then you can reconfigure your light strip on the Kasa Smart app.
How do I reconnect my LED strip light remote?
Reconnect power supply to power. With the remote, hold the ‘SPEED +’ and ‘SPEED -‘ buttons down simultaneously for 3 seconds (Figure 3). The indicator light should blink once to show you have done this correctly. The remote and receiver should now be paired and the light strip should be controlled by the remote.
How do you troubleshoot LED strip lights?
To troubleshoot, try the following steps: 1) Confirm that your power supply’s voltage and current rating are compatible with your LED strip. 2) Confirm that your power supply is working correctly. 3) Check and isolate other accessories on the same circuit. 4) Check for any visible loose connections.
What if your LED lights aren’t working?
Bad Pin Connection – If your LED strip light fails to turn on at all, then check your pin connections. Most likely, the pin is not inserted correctly. In rare cases, the pin is faulty. These tiny connectors are rather delicate items so you have to be very careful when inserting them.
How do I connect LED lights to my phone?
How to Use Smart LED Strip Lights with EZ Mode Step 1: Download LampUX App. Android and iOS users can go to the App store and download LampUX App on your phone, then register an account. Step 2: Set Up the Smart LED Light Strip. Turn on the LED strip lights and wait for 10 seconds. Step 3: Connect the App.
Why are my LED strips different Colours?
As established above, when LED strip lights don’t get enough cooling, they get overheated, and the diodes can change color. One of the biggest ways this can happen is poor air ventilation around the lighting setup. There is not enough space to carry away warm air and allow cooler air to circulate.
How do you stop LED strip lights from glowing?
How to stop led lights glowing when off? Replace the light bulb with a higher quality LED bulb. Grond the wiring. Install a neon indicator to soak up the extra charge.
How do you fix LED strips that won’t turn on?
Check for any visible loose connections, make sure all of your connectors and wires are in place and have not fallen out. Try tightening screws on DC adapters, and re-inserting LED strips into solderless connectors, which are common contact failure points.
Do LED strips burn out?
When they are connected correctly, smart LED strips rarely burn out. However, if too many strips are connected in series, this can lead to a circuit overload. The total resistance will be too high. This can lead to excessive heat being generated.
Why are my LED lights only red blue and green?
The brain actually interprets red as some excitation on the red cone and no excitation on the green cone. Green on the other hand has equal excitation of blue and red. In other words, the primary colour model is just not quite that simple. Adding more colours will in fact produce more detectable hues to the brain.
How long do LED light strips last?
HOW LONG DO LED LIGHT STRIPS LAST? LEDs boast a general life expectancy of 50,000 hours. This equates to around six years of continuous use. Over time, LEDs slowly and gradually lose their light output and 50,000 is the number of hours it generally takes for LED lights to diminish to 70% of their original light output.
How do you sync LED strip lights to music?
So, the best way to connect LED lights to your music is by turning on the music mode. And as long as the microphone is working and the music mode is turned on, the music will sync with the LED light making it pulsate to the rhythm.
Can you reprogram LED lights?
Introduction: How to Program LEDs They can also be programmed to change colour based on the different inputs received from the radio. For example, you can set the LEDs to show green when disarmed and red when armed. Or you can fade from one colour to another depending on how much throttle is applied.
Why do my LED lights have two colors?
If two primary color within the group of three LED elements are missing, this simply means that two surface-mounted components (resistors) have been damaged. Observe the PCB strip around the location of the missing primary color (red, green, or blue) and see if you see any damage.
Why are my LED lights not all one color?
LEDs, especially cheap LEDs (including most bulbs), tend to be very inconsistent in color. This is because the manufacturer does not tightly control binning, or separating LED batches by slight variations in color. Sacrificing binning cuts cost, but also consistency in light color.
Why are my LED lights only working on one side?
If half your LEDs are not working, it means that there are 2 strings of LEDs wired together in parallel – each parallel string has LEDs in series. You likely have a broken wire, or an LED bulb is broken or out of the socket.
Why did half of my LED strip lights stop working?
If the LEDs will not light up at all, then this could be down to a faulty power supply. Solution: If you have several power supplies, then try a different power supply onto the same strip to see if this now works. If it does, then you have a faulty power supply and will need a new one.
