Table of Contents
Follow these simple steps: First, turn off the power supply to the furnace by turning off the breaker in the circuit box. Locate the reset button on the furnace and press it to reset the furnace. If the button is popped up, press it down. Return the cover to the blower compartment and turn the power on.
Where is my furnace reset button?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
How long does it take for furnace to reset?
Either way, restarting a furnace is a relatively simple task that takes no longer than 10 minutes to complete. Follow these steps to reset your gas furnace: Turn the circuit breaker off and switch the furnace power button off too. Never touch the breaker with wet hands and use only one hand to do it.
How do I know if the control board on my furnace is bad?
If a control board starts to break, you will notice some of the following signs of malfunction: Warning lights. Typically, control boards have LED indicators that function as warning lights. Temperature instability. Interruptions in the event sequence.
How do you reset the ignition lockout on a furnace?
Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again. If your furnace has a pilot light, you may need to relight it following the manufacturer’s instructions.
How do I reset my furnace?
How to Reboot a Furnace Change the Filter. Before you do anything, check the furnace filter. Check the Pilot Light. If the pilot light is off, your furnace can’t get the spark necessary to light the boilers. Turn the Furnace Off and Back On Again. Call a Certified HVAC Professional.
Why is my furnace not kicking on when it should?
Ensure your furnace filters are clean: Your furnace won’t start up if it does not get enough airflow. Check your pilot light: If you have a gas furnace and gas supply is stopped your pilot light will go out. Check your blower motor: If the blower motor is not working then your furnace won’t pump out warm air.
What would cause a furnace not to kick on?
The Pilot Light (Faulty Ignition Sensor) The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. This is typically the problem if you can hear your furnace click on but it does not fire up. If the sensor or ignitor is dirty, it will need to be cleaned.
How much does it cost to replace a furnace control board?
A furnace control board replacement costs $300 to $650 on average. A furnace circuit board or motherboard costs $50 to $300 for the part alone, plus $250 to $350 for replacement labor.Furnace control board replacement cost. National average cost $450 Average cost range $300 to $650.
When should I replace my furnace control board?
If it is already 15 years old, getting a new circuit board may only add another five years or so to the life of the furnace. On the other hand, investing in a new furnace means you will have between 15 and 20 years of life.
How do I reset my electronic ignition furnace?
To reset the ignition control module on an electronic-ignition furnace, turn down the thermostat or turn off the power switch. Listen for the sound of the spark or watch for the hot surface ignitor to glow. Next, make sure the furnace’s flame sensor is clean.
What is a hard lockout?
Hard Lockout: Caused by a failure internal to the control or by a system fault such as flame out of sequence. A Hard Lockout will result in a no heat condition. To reset from Hard Lockout press and hold the “i” button for 2 seconds.
Where is the reset button?
Alternatively referred to as the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.
How do you reset a furnace blower motor?
How to Find and Reset your Furnace Motor Blower Step 1: Turn off the power to the furnace. Step 2: Remove the blower compartment cover. Step 3: Make sure the blower is completely cooled off. Step 4: Locate the reset button. Step 5: Press the button in (assuming that this is your issue and that the button has popped).
How many times can I hit the reset button on my furnace?
Don’t hit “reset” more than twice. The process pumps oil into the burner chamber, where it can accumulate if you have no ignition. Then when the furnace finally does start, it can do so explosively. So if the button won’t reset, or quickly pops up again, it’s time to call a professional repair service.
What does a solid red light on my furnace mean?
When lit, this red light, also called a lockout light, indicates that a safety mechanism on your furnace has caused a shutdown because it has detected a problem or recognized a fault. If your furnace has a digital display that provides a fault code, you can easily check the fault code to diagnose the problem.
Do old furnaces have control boards?
Gas Furnace Control Boards This type of board is a simple ignition control board usually found in older units, which tend to be less energy-efficient. It controls the operation of the gas valve, ignitor, and flame sensor.
