Table of Contents
How to Factory Reset Bissell CrossWave Max Click on the Hamburger menu button on the top left of the screen. Click on your Bissell CrossWave Max. Tap the gear in the top right corner of the screen. Choose the “Factory Reset” Button. Click on the red “Reset machine” button.
Why is my Bissell CrossWave Cordless not working?
Another reason you don’t have power could be because the handle isn’t inserted properly into the body of the CrossWave®. Push down on the handle. When properly inserted, it should “click’ into place. Remove the handle and re-insert into the body, push down until you hear a “click.”.
What does the red light on my Bissell CrossWave mean?
Your CrossWave® Cordless has an LED Light display that communicates different things about the battery to you. While using your machine if you see 3 solid red lights it indicates there is a clog in the brush roll. Turn machine off by pushing the Hard Floor button twice to remove obstruction.
Why does my Bissell CrossWave keep beeping?
If a Bissell CrossWave robot detects a problem, it will stop, produce a beeping sound, and the button light will flash or produce a solid light. Turn the robot OFF and remove hair and debris from the wheels.
Why does my Bissell CrossWave keeps shutting off?
If your machine turns off automatically again, unplug your machine and remove the nozzle. Hold the tab on the brush roll and spin the other end. Check the drive gear where the brush roll goes into the foot of the machine and remove any debris that may be wrapped in that area. Reinstall the brush roll and the nozzle.
Why is my Bissell not suctioning?
Check to make sure the Vacuum Suction Knob is turned towards “Floor Suction.” Or there could be large debris clogging the brush roll rotation. Your dirt container may not be seated properly or may be full. Check your hose for any cracks or holes that can cause loss of suction.
How do I know if my Bissell CrossWave is working?
To check the battery status, remove the Bissell CrossWave from the charging base and turn the machine on. You will know when the battery is fully charged when all three white status lights are illuminated. If you have tried everything, you may need to perform a factory reset.
How do you prime a Bissell CrossWave?
To start the machine, plug it in, then choose either the Hard Floor or Rug setting. Recline your machine and the brush roll will start spinning. Hold the trigger for ten seconds to prime your machine with water and cleaning solution. Your CrossWave is now ready to start cleaning.
Can you replace battery in Bissell CrossWave?
A: Hi Patti – the battery can be replaced at a BISSELL Authorized Service Center if necessary and is covered under the manufacturer warranty. We don’t offer a replacement battery consumers can purchase and install themselves.
Do you hold trigger on Bissell CrossWave?
CrossWave is the best way to clean sealed hard floors. Then hold your CrossWave over the stubborn mess while holding the spray trigger. Using short passes while holding down the trigger, the multi surface brush will go to work.
Why does my Bissell Bolt keeps turning off?
Your brush will automatically shutoff if it is bound by too much hair. A blinking red light will indicate this. Turn over of the foot of the machine to expose the brush roll. Place the brush roll back into the foot, then secure it into place by locking the tab.
How do I know if my Bissell CrossWave Max is charging?
Make sure your CrossWave® is fully charged before first use. To check the status, remove it from the charging base and turn the machine ON. You’ll know the battery is fully charged when all three white status lights are illuminated.
Why does my vacuum shut itself off?
A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. If the suction motor continues to trip the overload, you may need to replace the motor because the motor windings are bad. Bad windings could be causing the motor to overheat and trip the overload.
How do I reset a Bissell vacuum?
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Where is the reset button on my Bissell CrossWave?
The factory reset button on a Bissell CrossWave Max is located on the handle. It is the “Mode” button with the gear icon.
Why is my vacuum blowing out air?
This can happen when the vacuum suctions up something that is too large or that clogs the hose or nozzles, such as pine needles during the holiday season. To check, disconnect power to the vacuum and remove the hose. Check for objects that may be causing the problem and clear out the nozzle with a clean cloth.
Why is my Bissell vacuum not charging?
Cordless Bissell vacuum cleaners might have no power due to a dead battery, a faulty charging station, or a non-operative wall outlet.
Can I use Bissell CrossWave without water?
Yes it can be used as a vacuum without water. It actually vacuums better than many vacuums on the market.
How long does the Bissell CrossWave cordless Max battery last?
The BISSELL® CrossWave® Cordless Max combines tasks, vacuuming and washing at the same time, so you save time. The 36V lithium-ion battery provides up to 30 minutes of cordless cleaning power*, so you can move throughout your home without being tied to an outlet.
How long does battery last on Bissell CrossWave?
The internal battery lasts around 25 minutes of use, after which you have to wait four hours for it to recharge.
