Table of Contents
How to Reset a Ford Explorer Computer Open the hood: release the primary latch by pulling the release lever under the steering wheel near the floor board. Disconnect the negative battery terminal. Wrap the negative clamp in a towel. Leave the negative battery cable off for a minimum of five minutes.
How do you reset the check engine light on a 2017 Ford Explorer?
A few different ways to reset your check engine light are: Let it go off by itself. Turn your ignition on and off several times in a row. Disconnect your battery and reconnect it. Buy an OBD II scanner (they’re relatively inexpensive) and follow the instructions (it’s pretty easy).
How do you reset the oil change light on a 2018 Ford Explorer?
How To Reset Oil Life Light On Ford Explorer Switch the ignition over to the on position. Go to the SETTINGS menu. Scroll and select VEHICLE. Scroll down to OIL LIFE RESET. Press and hold the OK button. Shut the vehicle off and then start it back up and check the oil change light should be gone.
How do you reset the service engine soon light on a 2003 Ford Explorer?
Explorer Addict Just unhook the negative terminal for a few minutes and it should reset. OBDII resets the light anyway once the problem is gone, so if you think you’ve fixed the problem and the light is still on its prob. still there. The code will be stored in the computer but the light should be gone.
How do you reset the maintenance required light on a 2007 Ford Explorer?
2007 Press the SETUP button until the display reads “Press Reset To Begin System Check” Press the RESET button to display “Hold Reset If New Oil” Press and hold the RESET button for 2 seconds and release. The oil life is now set to 100%.
How do I clear my check engine light without a scanner?
To reset a check engine light without a scanner, disconnect the negative battery cable and wait a few moments. This will reset the diagnostic system in your vehicle, and if the underlying issue has indeed been resolved, the light should go off immediately.
How do I reset my car without disconnecting the battery?
How To Reset Car Computer Without Disconnecting Battery 3.1 Step 1: Open the hood and disconnect the battery. 3.2 Step 2: Locate the car’s fuse box and remove the fuse. 3.3 Step 3: Reinstall the fuse and reconnect the battery terminal. 3.4 Step 4: Start the vehicle and perform a test run.
What does the wrench light mean on a 2006 Ford Explorer?
The 2006 Ford Explorer wrench indicator light means you have a concern in the fly by wire throttle actuation. You no longer have a cable, but a computer controls the throttle for speed opening or a trans concern. The most common problem is the throttle position sensor on the throttle body is bad.
How do you reset the check engine light on a 2010 Ford Explorer?
Insert the key into the ignition to do this, turn the car on for about a second, then off for about a second. Do this two times more then drive the car as normal. This can be done by putting the car on and back off three times in quick succession.
What does the wrench light mean on a 2010 Ford Explorer?
If You see the wrench light turn on in the dash of Your 2010 Ford Explorer this means that Your ECU has detected a fault. I recommend getting off the road as soon as possible because continuing to drive can cause more damage to Your SUV.
How do you reset the change oil light on a Ford Explorer?
To reset it, go ahead and turn Your ignition to the ON position but do not start the engine. Now, on Your cluster, press the Select button and head to Set Up Menu Hold Reset. Hold the Select button for around 3 seconds and then let it go. Press the Select button again until You get to Hold Reset If New Oil.
How do you reset the oil change light on a Ford?
Press and hold the trip/reset button until the display reads “OIL LIFE SET TO 100%.” Turn the ignition to the “OFF” position. Start the engine and verify that the oil change required message is no longer displayed.
How do you reset the oil change light on a 2011 Ford Explorer?
To reset the ford explorer oil life light, put the ignition into on without starting engine. Use the pad on the steering wheel to scroll through the settings. Go to settings, vehicle, oil life reset. Push and hold ok.
How often does a 2020 Ford Explorer need an oil change?
An oil change is one of the most instinctive and abhorrent services for your car. Synthetic oil commonly should be changed every 7,500 – 10,000 miles. Ford recommends getting your 2020 Ford Explorer oil & filter changed every 3,000-5,000 miles for conventional oil.
How much oil does a 2020 Ford Explorer take?
Capacity: 5.2 quarts. . (with filter)After refill check oil level.
How do you reset the check engine light on a 2014 Ford Explorer?
To reset the 2014 ford explorer check engine light, insert the key into the ignition, turn the vehicle on for a second, then off for another second, then repeat two more times.
What does service engine soon mean on Ford Explorer?
If the check engine light in your 2021 Ford Explorer starts flashing, that means that the problem needs immediate attention and your Ford should be brought in straightaway. This blinking light frequently indicates a severe engine misfire allowing unburned fuel to be dumped into the exhaust system.
