Table of Contents
Can you replace a water heater element yourself?
The task of replacing a water heater element may seem difficult, but most homeowners can make this repair themselves. If your water heater is slow to heat, runs out of hot water, or doesn’t deliver hot water at all, there’s a good chance that one or both of your heating elements are not working properly.
How do I know if my water heater element or thermostat is bad?
If you turn the hot water tap and cold water runs out, then the upper thermostat is damaged. But if the water is hot that becomes later becomes cold, then you have a damaged lower thermostat.
Do you have to drain the water heater to change the thermostat?
Always disconnect the power or shut off the breaker before doing any work on a water heater. To change thermostats, you will need to remove the access panel and safety cover (do this for both upper and lower access panels on dual element units).
How do I know if my thermostat or element is bad?
Answer: Check for voltage at the element. If it has voltage the new element isn’t working. If no voltage there is a problem with the thermostat, either it is set too low or not functioning properly.
Are electric hot water heater elements Universal?
There are three types: screw in, bolt in and clamp in. They all have different wattage ratings and can work on either 120 or 240 voltage. Check your state and local codes before starting any project.
Will a water heater work with one element?
Yes, a water heater can still run if the bottom element quits. In most water heaters, the top heating element controls the thermostat and will still work even if the bottom element fails. So provided the top heating element is working, it can still produce some hot water even if the bottom heating element fails.
What happens when a heating element goes out in a water heater?
If you have an electric water heater, the heating elements inside the tank can break and lead to a loss of hot water. Sometimes, your water will slowly start to cool down and this could be because the element has burned out. If the second element fails, you’ll be left with only cold water.
How do I reset my water heater thermostat?
Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unit—and then behind some insulation. Once you find the button, push and release it.
How do I know if my thermostat is low?
Test the lower portion of the thermostat, by touching one lead to the common terminal (next to the temperature setting) and the second lead to the left heating element terminal. If the water in the tank is below the thermostat’s set temperature, the multimeter should read close to zero ohms of resistance.
Why does my hot water heater have two thermostats?
An electric storage-tank-style water heater has two thermostats because it has two heating elements. The thermostats are designed so only one element is active at a time. The reason only one element is active at a time is because it allows for smaller wire sizes and lower amperage demand when in operation.
How much does it cost to replace a water heater thermostat?
The average thermostat replacement cost is between $100 and $300. Most other repairs are equally affordable. There are two main types: gas and electric. A gas unit works by way of a gas flame while an electric one works using electric elements, or coils.
Should you replace both water heater elements at the same time?
Both heating elements generally do not work simultaneously. The only way to know which one is working would be to monitor the voltage at each heating element. I recommend replacing both elements since you have to drain the tank to clean flush the sediment out anyway.
Should both water heater elements be on at the same time?
Only one element will come on at any one time. This is known as a flip/flop system. On a 240 volt water heater, there will always be 120 volts to both elements. When the tank is full of cold water, the upper thermostat will take priority and heat up the top portion of the water to the setting of the thermostat.
Are hot water heater thermostats universal?
No, all water heater thermostats are not universal. There are some variances in thermostats between single-element water heaters and dual-element water heaters. Also, there is a difference in the upper and lower thermostats in dual-element water heaters. Common residential dual-element water heaters are 240 volts.
Can I replace a 3500 watt element with a 4500 watt element?
It is ok to install lower watt: replace 4500 with 3500 as long as voltage is same. Lower watt means less heat, so element can last longer.
Are water heater elements brand specific?
A flange type is not as common in newer water heaters. If you can’t find one, look for an adapter kit. With this kit you can replace the old flange style with a newer screw type. In most cases you do not have to buy brand specific elements.
Are upper and lower hot water heater elements the same?
Upper and lower heating elements are identical, and the temperature is regulated by the upper and lower thermostat and high limit device. Electric water heater elements can be different in size, but the most common is 12″ (300 mm).
