Table of Contents
What kind of walls are in a mobile home?
Manufactured homes usually use vinyl-on-gypsum (VOG) wall panels rather than standard drywall. Instead of using tape to cover the seams, as is done with drywall, the joints are covered with batten strips during assembly.
Can you remove a wall in a mobile home?
Typically, you can remove interior walls in a manufactured home as long as it’s not load-bearing. Load-bearing walls are usually the exterior walls and walls along the marriage line of a double wide.
How do you drywall a mobile home wall?
Steps to hanging drywall Step 1: Before You Begin. Remove molding, baseboards, batten strips, outlet covers and wall switches. Step 2: Measure & Cut. With a chalk line or straightedge, mark cut line. Step 3: Hang Panel. Step 4: Fasten Panel. Step 5: Fit Upper Panels. Step 6: Cut Around Outlets. Step 7: Fit Lower Panels.
How are mobile home walls constructed?
Mobile home walls are constructed much like the floors. They consist of a framework, usually in H-shapes, of wooden joists and supports. The space in between these joists forms cavities that are also used for insulation material. Both the interior and exterior of the walls are then covered in panels.
How can I make my mobile home walls look better?
Here’s the process they recommended: Step 1: Wash the Walls. Step 2: Use High-Quality Primer and Paint. Step 3: Use High-Quality Brushes and Rollers. Step 4: Use Several Light Coats. Best Primers to Use on Mobile Home Walls: Best Paint Brands for Vinyl Walls in Mobile Homes. Paint, Wainscoting, and New Trim.
Do manufactured homes use drywall?
The most common type of wall used for a manufactured home is called Vinyl-Over-Gypsum or VOG for short. VOG is drywall that is coated in vinyl wrap. This is different way of treating drywall as compared it being taped, floated, textured & painted.
Can you remove walls in a single wide mobile home?
Single-wide mobile homes have lightweight wood trusses that span between the two long walls of the home. So you can remove any interior walls without fear of having a structural failure.
Are mobile home walls load-bearing?
Do Mobile Homes Have Load Bearing Walls? Single wide mobile homes do not have load-bearing interior walls, but double wides do. For example, some companies screw the wall studs to the roof studs. A double-wide mobile home is basically two single wides connected to one another by what is called the ‘marriage line.
Are there studs in mobile home walls?
Manufactured homes are largely built the same. There are still manufactured homes built with 2”x3” interior wall studs, however. Keep in mind that interior, non-load bearing walls are simply dividing up the interior space of the home and are not structural.
What size drywall is used in mobile homes?
Manufactured home wallboards range in thickness from 5/16” to ½”. The 5/16” thickness used to be the most popular measurement for Paper On Gypsum (POG) wallboards, but the majority of new Clayton homes with POG wallboards are now 3/8”.
How can I cover my mobile home paneling?
Lightly Sand the Wood Paneling. For wood paneling only, your first step will be to lightly sand the walls with a very fine grit paper. Clean the Walls. The second step is always the most important. Tape the Wall. After the wall is completely dry start taping off your trim, carpet, and ceilings. Prime the Wall.
Is drywall too heavy for mobile home?
Drywall that is 5/8″ thick is, of course, a little heavier, at 2.31 pounds per square foot or 73.92 pounds per sheet which is entirely too much for mobile home ceilings.
How do you hang a heavy wall on a mobile home?
Use interlocking adhesive strips that are designed to hold objects on walls. These strips are two-part hangers that adhere to each other after they are mounted. Place one set of strips on the back of the item you wish to hang. Hold the item to the wall to take note of where you want to place it.
How do you repair a VOG wall?
Manufactured Home Wall Repair Patch Step 1 – Sand lightly around damaged area of wall. Step 2 – Apply spackling compound to back of match. Step 3 – Place patch over damaged area. Step 4 – Spread compound over patch, then let dry. Step 5 – Sand, then apply texture or paint for desired appearance.
How do you cover seams in manufactured home walls?
Mobile home manufacturers cover walls with panels of vinyl board and fasten them in place with battens. Contractors refer to the battens that cover seams as “batts.” Remove batts to expose the raw seams, then use a plaster product or joint compound with drywall tape to eliminate the seams in mobile home walls.
What is a VOG wall?
VOG walls are simply a 3/8” or 1/2” drywall pre-finished in a vinyl coating. These vinyl coatings come in many different patterns and colors, and, depending on the manufacturer, may be pre-selected for installation by the factory or custom selected by the home buyer.
Do modular homes have real walls?
A modular home comes standard with finished drywall throughout, primed and ready for your choice of paint or wall covering.
