Table of Contents
VSS Replacement 1) Loosen and remove negative battery cable. 2) Locate the faulty speed sensor and disconnect the speed sensor connector. 4) Check the connector wiring to insure there are no breaks or exposed wire. 5) Verify O-ring is installed on new sensor. 6) Install and tighten new sensor.
Is it easy to replace speed sensor?
The anti-lock brake system of a vehicle uses a wheel speed sensor to determine the speed of the moving wheel in order to control the anti-lock brake or traction control functions. Fortunately, it is easy to replace a wheel speed sensor and takes you about an hour at maximum.
Where is the speed sensor located?
Hello, the speed sensor for the speedometer is located on the transmission at the rear extension housing. The housing is the part that the driveshaft slip yoke (front part of driveshaft) would be position at. The sensor is attached with a bolt that needs to be removed, it has a two wire connector going to it.
How much is it to replace a speed sensor?
To replace the speed sensor, you are going to pay, on average, between $330 and $380. The labor should only cost you between $80 and $100, while parts will run you about $265.
How long does it take to replace a speed sensor?
Remove the old speed sensor. Replace it with a new one. The connector is in a plastic box hanging on the wheel well. 20 minutes.
Do you have to reset ECU after changing speed sensor?
You don’t need to reset anything but you can disconnect battery for say an hour if you want to do it.
Can you drive with a broken speed sensor?
Can you drive with a bad speed sensor? In general, it is unsafe to drive a vehicle with a broken wheel speed sensor. The car’s computer will not be able to determine the speed that your vehicle is traveling, so it might apply the brakes at a faster rate than necessary or increase the engine power.
What happens when your transmission speed sensor goes out?
When there’s no speed signal coming from the sensors, shifting of gears will be a problem because the powertrain control module won’t control them correctly. This will make the transmission not work properly. It will either shift more quickly or roughly than expected.
How many speed sensors does a car have?
Modern vehicles have four wheel speed sensors: two front wheel speed sensors and two rear wheel speed sensors. That is, each wheel of your car has a wheel speed sensor.
What causes a vehicle speed sensor to malfunction?
Also, the plastic portion of the sensor can become brittle after prolonged exposure to the elements. The magnetic portion of the sensor may also become worn and damaged over time. The speed sensor measures the rotation of a toothed wheel on a shaft inside the transmission to determine how fast your car is going.
Can you clean a transmission speed sensor?
The transmission speed sensor measures the RPMs of the shaft of the transmission. In this case, the sensor may not have to be replaced as the sensor can be cleaned off. Yet, only a mechanic should make that determination because there may be damage to the electrical part of the sensor.
What is P0500 code?
Diagnostic trouble code (DTC) P0500 stands for “Vehicle Speed Sensor (VSS) Malfunction.” This code is set when the PCM or engine control module (ECM) detects incorrect speed readings or no signal at all from the vehicle speed sensor (VSS). Vehicle Speed Sensor “A” Intermittent/Erratic/High.
Which speed sensor controls the transmission?
Typically, two sensors communicate the transmission data to the vehicle’s powertrain control module. The first sensor, referred to as the input sensor, monitors the speed of the transmission’s input shaft. The second sensor is the output sensor, which monitors the output shaft speed.
Is it hard to replace an ABS sensor?
You’re driving down the road when suddenly, the antilock brake system (ABS) warning light pops up on the dashboard. The good news is, replacing an ABS sensor is usually a straightforward task. In most cases, all you need to complete the job is a jack, jack stands, and basic hand tools.
How long do speed sensors last?
There’s no hard-and-fast rule to help you predict how long your wheel speed sensor is going to last. Unlike a brake light switch or brake caliper that can last as long as your vehicle, you can expect your transmission speed sensor to last between 30,000 and 50,000 miles.
Can disconnecting battery reset ECU?
A. It depends on the car’s age and type of ECU used. On some older cars, disconnecting the battery will reset the system but in most new cars it does nothing, except potentially reset the clock and radio station presets. Some ECUs have “adaptive learn” features for auto transmissions.
How many miles do you need to drive to reset computer?
So why is the light still on? Here’s something you probably don’t know: after clearing the car’s computer you will need to drive for about 50 to 100 miles. As you drive your car the computer will monitor all the sensors and register the results.
How do I reset my ECU without a scanner?
After removing the battery cables, you should proceed to cycle the ignition switch to the ON and OFF position for 3 to 5 times. Press on the horn button in the steering wheel. Keep it pressed for 30 seconds to a full minute to drain out all the stored power in the ECU capacitor. The horn is connected to a hot circuit.
How do you remove a broken speed sensor?
How to Remove a Stuck or Broken Speed Sensor Pry underneath the sensor with a flat blade screwdriver. Remove the sensor. If the sensor is still stuck, drill three holes into the sensor without drilling too far down. Remove the rubber o-rings. Pry out the sensor with a flat tip screwdriver.
How can you tell if the transmission sensor is bad?
Top Signs of a Failing Transmission Position Sensor Car fails to move out of park. When your vehicle is unable to shift out of neutral or park, this is a clear indication that there is a serious problem somewhere in the transition system. Transmission shifts into the wrong gear. Vehicle becomes locked in a single gear.
