Table of Contents
Is it easy to replace a shower drain?
Replacing a shower drain isn’t usually a difficult task, but it always pays to be prepared for complications before you start the job, especially as every project is different.
How much does it cost to have a shower drain replaced?
Install a Shower Drain: national average cost The national average materials cost to install a shower drain is $56.20 per drain, with a range between $50.42 to $61.98. The total price for labor and materials per drain is $304.76, coming in between $276.31 to $333.21.
How do you fix a shower drain without removing the pan?
Fixing a Leaking Shower Drain Without Taking Out the Pan Remove the drain cover. Discard the compression gasket. Remove the shower drain body. Clean the rim of the drain. Install the new gasket. Screw in the new shower drain body and seal it with putty. Remove any excess putty from around the drain.
How do you remove a PVC shower drain?
REMOVAL OF EXISTING SHOWER DRAIN BODY Remove drain cover with flat blade screwdriver. Remove the crown nut by unthreading it using needle nose pliers. Extract the compression seal exposing drain pipe and shower drain body. With mini hacksaw, make two vertical cuts approximately 1” apart through drain body.
Does a shower drain need a trap?
Do shower drains have traps? According to regulations, all shower drains are required to have P-traps. This includes all fixtures connected to a building’s main plumbing system. P-traps are curved pipes installed under showers and drains of all kinds.
How do I install a shower drain with no access from below?
How to install shower drain without access below: Remove the existing shower drain. Measure and cut the assembly parts. Clean the area and pipes. Assemble and install the new drain. Apply a sealant and tighten the shower drain. Clean excessive sealant. Install strainer cover. Conduct a leak test.
How do you remove a shower drain UK?
Use a rag to prevent scratching, or you use a rubber grippy. Use a flathead and unscrew the brass inserted below and lift the stopper. Some pop-up drain covers pull up and off while some have to be wiggled back and forth. Covers that are rocker-arm style must be pulled to clear the drain.
What is a shower drain flange?
A bathtub drain flange is the finished drain part that’s visible in the tub. Some manufacturers refer to the drain flange as a “drain body” or “drain basket”. Between the underside of the flange and the tub surface, there’s a good amount of plumbers putty that seals the inside of the drain.
Do I need a plumber to install a shower?
Replacing an electric shower still requires plumbing and electrical experience, as your new shower may have higher wattage. Rather than attempting to tackle the job yourself, you should always call in a qualified plumber who will ensure your electric shower is replaced safely.
How much does it cost to install a linear shower drain?
Most linear shower drains cost $200 or more, though you can find some for as low as $100. Because linear shower drains require more coordination between the tile contractor and plumber, you may also need to pay a few hundred dollars more for labor, especially if working with someone who charges hourly.
How much does it cost to install shower plumbing?
How Much Does a Plumber Cost? To install the plumbing for a standard shower, a you’ll likely pay $50 to $200 for a plumber. This price increases if the plumber will need to install any additional features.
Are shower drains glued?
This type of drain comes in both PVC plastic and ABS. The glue on shower drain can be used with plastic shower bases, fiberglass and steel. Be aware that when using a gluon fitting it can be more difficult to get the measurement of the pipe correct.
Where is the P-trap in a shower?
A shower P-trap is located beneath the shower drain hole. It may be one solid piece of pipe or it may be an extension pipe attached to a J-bend pipe to form a “P.” P-traps are removed using the same process in either case. Access to the P-trap is the key element in the process.
What is the standard size pipe for a shower drain?
Keep in mind that shower drain assemblies are generally made to fit a 2-inch drainpipe, not the 1 1/2-inch pipe usually found on tubs. A 2-inch pipe is the recommended size because showers have a low threshold for flooding, and a 2-inch pipe helps the water drain faster than does a 1 1/2-inch pipe.
How do you remove a oatey shower strainer?
The easiest way to remove the strainer is to weave a string or small wire through two openings near the edge of the strainer and pull straight up. It is not recommended that you pry the corner up because it could damage the shower base surface.
Is it possible to move a shower drain?
Sometimes moving a shower drain requires removing a concrete floor. Many bathroom remodeling jobs involve moving or replacing the shower stall. This often requires moving a drain connection that penetrates a concrete floor.
Does the shower drain have to be under the shower head?
You can put a shower drain opposite of the showerhead. This is a common option for property owners depending on the layout of their plumbing. As long as the shower drain is at the bottom of the slope, this will ensure water flows down the drain as expected.
