Table of Contents
How To Replace Roof Fascia Board Step One: Inspect the Existing Fascia. Step Two: Remove Gutters and Drip Edge. Step Three: Remove Existing Fascia Board. Step Four: Measure and Cut. Step Five: Cover the Seams. Step Six: Seal the Wood. Step Seven: Install Drip Edges and Gutters.
Can I replace fascia myself?
Luckily, replacing a fascia board is as easy as taking out the old board and fitting a new one in its place. Once you’ve installed a new board, all you need to do is seal the seams and paint it to match your home. With a short afternoon renovation, you can have new fascia boards that will last for years!.
How much would it cost to replace fascia boards?
1. Average Cost to Replace Fascia and Soffit Cost Per Linear Foot Total Cost* Low Cost $6 $1,500 Average Cost $10 $2,500 High Cost $20 $5,000.
How do you fix rotted wood fascia?
Soffit and Fascia Repair Remove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. Remove Rotted Fascia. Remove the rotted section of fascia. Remove Old Soffit. Pull down to remove the old soffit. Remove Rotted Rafter. Attach Cleat. Attach New Rafter. Seal Replacement Soffit. Attach Replacement Soffit.
What is the best material for fascia boards?
Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.
Can you use Hardie board for fascia?
HardieTrim board is a decorative non-load bearing trim product. Do not use HardieTrim to replace any structural component. HardieTrimboards can be fastened directly over a 2x sub-fascia or directly to rather tails.
How long do fascia boards last?
Well installed and maintained wooden fascia can last for up to 20 or 30 years, before they start deteriorating. Although some might need replacing within 5 to 10 years.
How wide is a fascia board?
Fascia Board Sizes Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction. Therefore, the more common fascia board sizes are 1×6 or 1×8.
What is the board behind the fascia called?
Soffit is the layer of wood, vinyl or aluminum that extends from the bottom of the fascia to the top piece of your wall board. Together, they protect the rafters from weather, moisture, and allow air to flow through soffits and vents.
How do you fix the end of rotted fascia?
Steps 1Measure the existing fascia board and prepare tools. 2Remove the guttering from the fascia board. 3Lift the roof off the top of the fascia board. 4Mark the line where you will cut the fascia board. 5Cut the fascia board. 6Remove the old fascia board and replace it.
How is fascia attached?
The fascia board is nailed to the rafter feet and usually has a rebate or lip for the soffit boards to slot into. They are then either fixed to a batten that is attached to the brickwork, or sat on top of the last course of brickwork.
What is another name for fascia board?
The fascia board is the one mounted at the point where the roof meets the outer walls of the house and is often called the ROOFLINE. However most people refer to it by the name of the main board that carries the gutter – the fascia or fascias.
Can PVC be used for fascia board?
Obviously the biggest reason for using a PVC trim board is long term maintenance combined with traditional architectural appeal. PVC trim boards will not rot, twist, split or warp. In addition you can leave it unpainted if you like or paint it to match a certain color scheme.
Can you use treated lumber for fascia board?
Purchase pressure-treated lumber to replace your fascia boards as a way to extend the life of the repair. Pressure-treated lumber is designed for outside applications and resists rot, moisture and insect damage. Cut the new lumber to size and secure it to the rafter ends with galvanized finish nails.
What is the best wood to use for fascia board?
Many different types of wood are suitable for fascia boards. Spruce, pine and fir are all popular and relatively inexpensive options. However, some roofers prefer to use cedar, cypress or redwood for fascia boards. While they are more expensive, these woods better resist moisture, even when left unsealed.
Can cement board be used as fascia?
Soffits and fascia board We used fiber cement board to close in the soffits and cover the fascia of the house. Any rotted fascia boards should be replaced prior to covering. The fiber cement board, although durable, is not structurally adequate to support the eaves on its own.
Is Hardie trim discontinued?
While your preferred siding brand may have discontinued production for some of their products, you should not be afraid as many options are available. For instance, recently, James Hardie has discontinued their trim supply in 2021 for the Pacific Northwest.
Do you need scaffolding to replace fascia?
In some instances, scaffolding will be recommended – such as for a typical 3 bedroom semi-detached house on two floors, replacing soffits and fascia board will require the erection of scaffolding.
When should you replace fascia?
An ideal time to replace damaged fasciae and soffits is when you have a contractor install a new roof. If your roof replacement is an insurance restoration, ask your claims adjuster to include the replacement of any damaged fascia or soffit.