Table of Contents
When should I replace my Cricut knife?
Cricut machines blades need to be changed at different intervals based on the materials you use with your machine. In general, when the cuts are not crisp, then it is time to change your blade.
How do you tell a Cricut blade apart?
You can easily identify this blade in retail locations by the red or white protective cap. The blade housing that ships with the Explore machines was designed to house the Premium Fine-Point blades. The Cricut Explore Deep Point blade has a steeper blade angle (60 degrees vs. 45) and harder, more durable steel.
How long will a Cricut blade last?
When asked, “How long do Cricut blades last?”, we think for a guideline you could start with, that at a minimum, you should change your blade every two months with average use of your Cricut machine. If you’re cutting with it quite often, you might need to move that up to every six weeks.
Are Cricut blades interchangeable?
Are Cricut Blades Interchangeable? The Fine Point blade and the Bonded Fabric blade can use the same housing. Also, the QuickSwap tools can use the same housing, so if you already own one, from now on, you only need to get the tip or blade.
How do I fix my Cricut blade?
How do I fix my Cricut not cutting correctly? Ensure that the blade depth is deep enough to cut cardstock. Increase the pressure to the highest setting. Make use of a Circut brand blade. Remove the blade and reinsert it the correct way – the cone point end should not be the side sticking out.
What blades come with the Cricut maker?
The Cricut Fine-Point Blade is the standard blade that comes in both the Cricut Explore and the Cricut Maker. It was previously called the “Premium German Carbide blade,” but is now just referred to as “Fine-Point.”Feb 6, 2020.
Are Cricut explore and maker blades interchangeable?
Cricut Explore holds the Scoring Stylus and a cutting blade at the same time, so you can cut and score in one step—without changing mats! Also compatible with Cricut Maker.
What Cricut blade cuts wood?
The Cricut Knife Blade is a tool you can use with your Cricut Maker that cuts through thicker and denser materials such as balsa wood, leather, matboard, and Cricut Chipboard easily. You can buy it complete with the Drive Housing here.
How long does a Cricut blade last cutting vinyl?
A Cricut premium fine point blade should last 12-18 months. Daily use and cutting heavy materials will dull your blade sooner. Paper and cardstock tend to dull your blade faster than vinyl. When your blade stops cutting well, even after cleaning and adjusting settings, it’s time to replace it.
How long do Cricut fine point blades last?
It depends on a few factors including how often you use your machine and what type of materials you cut. In general, 3-6 months is the average useful life of a Premium Fine Point blade in a Cricut Maker machine.
Do you need to oil your Cricut?
Simply wipe these particles with a soft, clean cloth. Some grease is necessary for smooth operation of the machine, but if you see grease buildup on the carriage shaft, use a cotton swab, tissue, or a soft cloth to gently remove it.
Why is my blade cutting through my vinyl Cricut?
In general, your cutting machine cuts through the vinyl backing if the settings are incorrect, usually, the pressure is too high. Adjusting your pressure, changing your blade, and doing test cuts can fix it for your next try. Meanwhile, transfer tape and patience can salvage most projects with cut backing.
Why is my Cricut blade not going down?
Inspect the blade and blade housing and remove any debris that may be stuck to the blade or lodged in the blade housing. Once clean, perform a test cut. Replace your blade with a new Cricut brand blade. Blades can become dull with use and replacing them with a new, sharp blade often solves this issue.
How do I make my Cricut mat sticky again?
Run lukewarm water over the mat. Use a plastic, hard-bristled brush to gently scrub in a circular motion until the entire surface of the mat had been cleaned. Pat dry with a paper towel. Let mat air dry completely for stickiness to return.
What is the deepest cut setting on Cricut maker?
When it comes to using the Cricut Maker, you have more than 300 materials to choose from. For the Cricut Maker, the thickest material the device can cut is 2.4 mm thick, giving you a greater range of options to choose from.
What Cricut setting cuts the deepest?
The Cricut Deep Cut Blade can cut most materials up to 1mm in thickness using the multi-cut feature.
Do I need a new housing for deep cut blade?
No. It is recommended only because it is a different color and will not get mixed up with the regular blade. It is the SAME HOUSING in a DIFFERENT COLOR. If you very meticulous and remove your deep cut blade and put it into a labeled container every time you use it, you should have no problem.
Can I use knife blade with Cricut explore AIR 2?
Can I use Knife Blade with my Cricut Explore machine? Knife blade is compatible with Cricut Maker machines only. It is operated by a drive mechanism that Cricut Explore models do not have, and with which they cannot be upgraded.
Can Cricut maker cut plywood?
You can cut either wood on the Cricut Maker machine. Whichever you choose, just make sure it doesn’t have any knots. If a piece as a knot, make sure the knife blade will not have to go through the knot when cutting your pattern.
What is Cricut knife blade?
Cricut Knife Blade The extra-deep Cricut Maker Knife Blade slices through dense materials up to 3/32” thick with unprecedented ease and safety. It’s ideal for cuts of moderate detail in thicker materials. Recommended to use with Thicker Materials such as balsa wood, mat board, and chipboard.
Can you sharpen Cricut knife blade?
Absolutely! Cricut blades are super easy to sharpen. You just need a few inexpensive and readily available supplies, including: Heavy-duty aluminum foil.
