Table of Contents
How do you replace damaged Hardie lap siding?
To remove and replace damaged siding: Cut the fiber cement siding to length (wear approved dust protection). Blind-nail the fiber cement siding in place, starting with the bottom piece. Face-nail the top piece of fiber cement siding through the old siding. Prime and paint new siding to match the old.
How do you remove Hardie plank siding without damaging it?
In order to remove the board you’ll have to pull out or cut off the nails, which are likely located underneath the overlapping siding on the row above. Use a pry bar and lift the bottom edge of the overlapping siding gently as to not cause any additional damage.
Can you repair Hardie plank siding?
Though it is a tough wearing product, the surface of the siding can sometimes be damaged during installation, by unusual wear or by impact. The James Hardie company, makers of HardiePlank, recommends the use of a cement patch product made of an acrylic mortar compound for patching their siding products.
Can Hardie board be repaired?
Fixing Hardie Plank Siding You can easily fix it by cleaning it and then using caulk to patch the gap. The best way to fix these gaps is to clean the joint and then patch it with caulk. This way water and other elements can’t go past the patch, between or behind the planks, and cause further damage.
How do you remove Hardie board trim?
Warning Slide the thin edge of a flat pry bar carefully under the lower edge of the first piece of HardiePlank siding to be removed. Pry the piece of siding out toward you gently to let you see the nail or screw patterning of how the planks have been fastened to the under-structure.
How much does it cost to replace Hardie siding?
Hardie Board siding materials cost $3 to $6 per square foot, and the labor cost to install is $3 to $7 per square foot. Old siding removal adds $0.25 to $1 per square foot when residing.
How do you remove Hardie siding from concrete?
For siding that has a porous or faux wood grain, spray the affected area liberally with white vinegar to soften the concrete while scrubbing it away with a stiff-bristled brush. Rinse the siding off thoroughly with water after using the scrub brush to clean off any remaining residue.
Does Hardie board peel?
The solution – Hardie® siding and trim products with ColorPlus® Technology. ColorPlus Technology by James Hardie provides a multi-coat, baked-on finish that resists damaging UV rays, chipping, peeling and cracking.
How do you fill nail holes in James Hardie siding?
ColorPlus® Products ColorPlus® Touch-up Kits can be used to cover nicks, scrapes and nail holes that may occur over time. If the touch up area is larger than the size of a dime, the use of ColorPlus® Touch-up Kit is NOT recommended. It is advised to replace the damage siding with a new section of ColorPlus® siding.
How do you cut cement board already installed?
Lay your cement board flat, and draw a line with a carpenter’s pencil where you intend to cut. Place a straightedge along the line and drag either a drywall utility knife or a scoring tool against it. Repeat your cuts two to three times to make them deeper, which will make snapping the board easier.
Do you have to caulk Hardie siding?
Ugly Caulking Wherever Hardie siding meets a trim board, the company recommends you leave a 1/8” gap between the siding and the trim and apply a 3/8” bead of approved caulking to protect and seal the edge of the siding.
Should you caulk Hardie siding?
APPLICATION: General: James Hardie believes it is good building practice to seal the joints to prevent moisture, such as wind-driven rain and snow, from penetrating the wall cavity. Caulking around windows, doors, eaves and trim edges gives added insurance that leaks will not occur.
Does caulking Hardie board void the warranty?
These such areas are called “field butt joints.” In the case of James Hardie’s Color Plus siding, which has a pro-rated 15-year warranty, using caulk at field butt joints will flat out void your warranty!Aug 5, 2013.
Do you need plywood behind Hardie board?
Fiber cement siding should be installed over plywood, OSB, or sheathing. Building codes will usually require installing siding over water-resistant barriers and nailed into the studs every 16 or 24 inches.
Can I use PVC trim with Hardie siding?
As a company that has installed HardiePlank® siding on hundreds of homes we recommend using 3/4″ HardieTrim® boards instead of PVC for fascia boards, rake boards and the 1″ NT3 (cement) for corner posts.
Does Hardie board increase value of home?
James Hardie Siding Does Increase the Resale Value of Your Home. Whether or not if you’re deciding to sell your home, having James Hardie Siding is going be one of the best investments you’ll ever make. According to Family Handyman, you can recoup as much as 76% of the upfront cost of it upon the sale of your home.
Can you screw into Hardie board siding?
HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel. Fasteners shall be installed between 1 in. and 3/4 in.
Can I install Hardie siding myself?
Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.
Can I pressure wash Hardie board siding?
Don’t use a high-pressure power washer to get the job done, as it turns out a low-pressure hose and a soft medium bristle (nonmetal) brush is the best way to remove dirt and debris from James Hardie® siding and trim.
Can you power wash cement board siding?
The manufacturer recommends that you do not pressure wash your Hardie siding. The hard spray of water from the power washer can damage the surface of the siding. In fact, pressure washing fiber cement siding is one of the only ways you can damage this durable type of siding.
Can you pressure wash cement board siding?
Do not use a high-pressure hose to clean fiber cement siding. This is one of the few ways that you can damage it. If you feel that you need to use a pressure washer, especially on harder to reach locations, only use it at a low pressure — under 1500 psi — with a wide tip.
