Table of Contents
How to Replace a Blower Motor Resistor Step 1: Remove the glove box door, if necessary. Step 2: Disconnect the wiring harness and remove screws. Step 3: Remove and replace the blower motor resistor. Step 4: Tighten screws and reattach wiring harness. Step 5: Reinstall the glove box door.
How do I know if my blower motor resistor is bad?
Usually a bad or failing blower motor resistor will produce a few symptoms that can alert the driver of a potential issue. Blower motor stuck on one speed. Blower motor does not work on certain settings. No air from the vehicle’s vents.
How long does it take to replace a blower motor resistor?
takes about 45 minutes.
Where is the heater blower motor resistor located?
The heater blower motor resistor is often found beneath the dashboard. It is located in the heater and air conditioning compartment. It’s connected to the air conditioning system, where it can adjust the speed of the blower motor fan. It can also be found behind the glove box of some vehicles.
How do you replace a resistor?
Take the circuit board on which the resistor is soldered and cut the wire leads with diagonal cutters. Remove the defective resistor. Turn on the soldering iron. Place the tip on the lead and the pad through which the lead is placed until the solder melts.
Why does my blower motor resistor keeps melting?
Trent, one of the biggest reasons for blower motor resistors to have shorten life is actually because of faulty blower motor drawing too many amps, some times melting wires/plugs, heating up resistors shortening their life. Many Dodge forums tell of this problem.
Is there a way to test a blower motor resistor?
Place one lead of the Ohmmeter on terminal 1 of the resistor. Place the other lead on terminal 2 and check against specifications. If this circuit is open, showing infinity on the Ohmmeter, the blower resistor must be replaced. Move the lead from terminal 2 to terminal 3 and check this reading against specifications.
How much is a motor blower resistor?
How Much Does a Blower Motor Resistor Replacement Cost? A blower motor resistor costs anywhere between $1 and $400. Factors that can affect its price include its condition, configuration, material, and set or kit inclusions. Labor may cost you an extra $45 to $55, depending on your area.
Why does the heater in my car only work on high?
Most car manufacturers use a series of resistors to make the heater blower motor run at different speeds. And when one or more of these resistors burn out, you’re usually left with only one heater blower motor speed—high. Remove the screws, and swap out the resistor module.
Why does my blower motor fuse keep blowing?
While the blower motor is clogged up, it can cause fuses to blow because it has to work hard to try to operate. The fuse is also attempting to run, and because it is unable, this increases the chances of a furnace fire.
Why is my blower fan not working?
Make sure that the power cord hasn’t melted or a fuse hasn’t been blown. If your cables are looking fine, try unplugging the fan for a few minutes and then plugging it back in again. If unplugging and plugging your fan back in again doesn’t work, check the fuse box.
Is there a fuse for the blower motor?
Many vehicles have two fuses for the blower motor, one in the interior fuse block and the other under the hood. The blower motor is usually under the dashboard on the passenger side.
Can I replace the resistor with another?
Sometimes you need a resistor with a value you don’t have in your kit. Instead of ordering and wanting for a resistor with a value you need you can change the resistance of a resistor by using another resistor or many. By installing resistors in a parallel or series circuit you can change the value in Ohms.
What happens when a resistor burns out?
When a resistor breaks down, current typically flows through the burnt resistor without any resistance and thereby passes unchecked. Other components in the circuit may become damaged from the excess current flowing through.
Why does my blower motor resistor keep failing?
In most cases, a blower motor resistor fails due to corrosion or overheating. Sometimes, the mechanical resistance to the motor rotation causes an excessive electric current that can overheat and prematurely damage the blower motor resistor.
Can a blower motor resistor be bypassed?
Blower resistors are made of several resistors with different resistances. In the highest speed state, the blower resistor is bypassed completely and the fan is connected directly to the car’s battery, which allows maximum current through the motor.
Can a blower motor resistor be repaired?
The average cost to replace the blower motor resistor at a repair shop is between $44 and $55 in parts and $70 in labor costs, for a total cost of around $114 to $125. On the other hand, you can easily fix the blower motor resistor at home in about an hour (even if you’re a beginner) and for around $70.
Can you drive a car without a blower motor?
Your car’s blower motor is not only necessary for the operation of your air conditioner. Without a functioning blower motor your engine runs the risk of overheating. Start car and see if blower motor works. If fuse blows again, check for loose circuits.
Why does my air only work on high?
The blower motor resistor is prone to shorts, corrosion, and overheating. When the resistor fails, typically, the highest setting is the only option that still functions. This is because the air from the blower motor is bypassing the resistor, thus gaining the maximum amount of voltage, resulting in full power.
Why does my heater fan only work on high?
When a resistor fails, the fan will often run only at higher speeds or the highest speed, no matter what fan speed is selected. If little air is coming through the vents (hot or cold), then it could be because the blower motor for the fan or a switch or resistor that controls fan speed isn’t working.
