Table of Contents
How do you change a ballast in a fluorescent light fixture?
Instructions Remove the Cover. Remove the lens, or diffuser cover, from the fixture. Remove the Fluorescent Tubes. Remove the light bulbs (fluorescent tubes). Remove the Cover Plate. Disconnect the Ballast Wires. Remove the Ballast. Prepare the Wires. Mount the New Ballast. Dispose of the Old Ballast.
How do you know if a ballast is bad?
If your fluorescent lighting is displaying any of the signs below, it could be a symptom of a bad ballast: Flickering. Buzzing. Delayed start. Low output. Inconsistent lighting levels. Switch to an electronic ballast, keep lamp. Switch to an electronic ballast, switch to a T8 fluorescent.
Do I need an electrician to replace a ballast?
Yes. In fact, you really need a locking device to replace the ballast. – An electrician replaces the ballast on a fluorescent lamp. He uses a switch on the wall to turn off the fluorescent light.
How hard is it to replace a ballast in a fluorescent light?
The ballast takes in electricity and then regulates current to the bulbs. You can get a new ballast at a hardware store or home center and install it in about 10 minutes. However, buying a ballast can be expensive, so consider pricing a brand-new fixture for comparison.
Why are my fluorescent lights flickering?
If your fluorescent bulbs flicker, most likely the problem is with the bulb itself. If the bulb is very dark on either end, it may be defective and burned out. The best way to test the functionality of a bulb is to put it into a fixture you know works. Flickering fluorescent lights can also be a result of temperature.
How do I know if my ballast is T8 or T12?
If no markings are available, the size in diameter of the tube is the easiest way to determine the type you have installed. T8 tubes are 1-inch in diameter and T12 tubes are 1 1/2 -inch.
How do you know if it’s the bulb or ballast?
One probe of the multimeter should touch the hot wire connections, while the other touches the neutral wire connections. If the ballast is good, an analog multimeter has a needle that will sweep to the right across the measuring scale. If the ballast is bad, then the needle won’t move.
Is it cheaper to replace ballast or fixture?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
Can anyone replace a ballast?
Yes. As a matter of fact, you do need a lock out tag out device in place for changing a ballast. ‘An electrician is replacing the ballast on a fluorescent light.
Can you repair a ballast?
While simply swapping burned out bulbs in an existing ballast is deemed “ballast repair” by many – and can offer advantages in longevity and energy savings – sometimes this simple “fix” is not enough.
Why does my fluorescent light work sometimes?
If a fluorescent tube blinks on and off-a slower and more distinct process than flickering-the fault may lie in loose wiring or in another component, called the ballast. The ballast is almost always to blame if the fixture hums during operation.
Why are my fluorescent lights not working?
A dead fluorescent can be caused by lack of electrical power (tripped breaker or blown fuse), a dead or dying ballast, a dead starter or a dead bulb(s). defective starters, defective bulbs or a defective ballast. IMPORTANT: Flickering fluorescent tubes can cause the ballast to overheat and fail prematurely!.
How long do fluorescent ballasts last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
Can a bad ballast cause flickering?
Dimming or flickering If your bulbs are very slow to reach full brightness or strobe periodically, there may be a problem beyond the bulb. Water-damaged or faulty ballasts often struggle to regulate current.
Can I use T8 in place of T12?
T8 tubes are simply 1 inch in diameter versus the 1.5 inch diameter of T12 tubes. In an effort to make LED tube lights compatible with the internal dimensions of most fixtures, you will find that most LED tube lights feature a T8 or 1 inch diameter. They can indeed be used in T12 fixtures.
What do the numbers on a ballast mean?
About Advance Ballasts and Fluorescent Lamps. Advance Ballasts that utilize fluorescent lamps usually come in two shapes, straight and u-shaped. Most fluorescent types are T5, T8, and T12. The T stands for tubular and the number provides the diameter in 1/8 of an inch. Therefore, a T12 ballast must use a T12 bulb.
Can I replace a T12 ballast with a T8?
The easiest and lowest price option to replace a T12 is a T8 linear fluorescent. They have become the go-to option for pre-existing T12s. If you still have magnetic ballasts, switching to a T8 will require a ballast swap. Another option is to move forward with an LED retrofit.
