Table of Contents
Is it hard to replace anode rod?
Even with a breaker bar, it can be nearly impossible to break the anode rod free. Turn off the power or gas. Then close the cold-water valve at the top of the tank and drain off several gallons. Loosen the hex head with the impact wrench, but unscrew it the rest of the way by hand.
How often should you replace the anode rod in a water heater?
Most water heater manufacturers will recommend inspecting the condition of the sacrificial anode every one (1) to three (3) years and replacing it when it has been consumed more than 50%. This is especially true if you have hard water or use a water softener.
How much does it cost to replace a water heater anode rod?
An anode rod costs about $50. Some homeowners may feel comfortable replacing it themselves. If not, call a professional plumber, who can assist. The cost of having it replaced professionally may be around $250 or $300.
What size socket do you need to remove an anode rod?
4 Use a ratchet wrench and 1 1/16-inch deep socket to unscrew the anode rod from the heater.
How long will water heater last without anode rod?
Diminished Water Heater Lifespan: Without a sacrificial anode rod replacement, the average tank water heater will last a maximum of 8-12 years. However, your water heater may start failing as early as 5 years old without this essential care.
Are anode rods universal?
Anode rods are not universal. Anode rods vary in length and material. Some anode rods are installed at the top of the water heater tank, while others are attached to the hot water outlet. However, the length and type of the anode rod may not be the same.
Is it OK to remove anode rod?
Yes, you can cut your sacrificial anode rod, whether it is magnesium or aluminum, to replace it. To do this, use a pair of gloves and a saw and cut as you remove the old anode.
Should you use Teflon tape on anode rod?
Yes, teflon tape may reduce the effectiveness of the anode rode by electrically insulating the rod from the water heater chassis. The chances of it completely isolating it are nearly impossible though. Use pipe joint compound if you have it, and use teflon tape if you don’t.
How do I know what size anode rod to buy?
As a rule you want the anode to be “tip to toe” running the full height or length of the tank. If you cant see your brand on the chart then just measure the length of the tank and pick the closest length of anode. If the anode is too long they can be simply cut to length with a hack saw.
Can anode rod causing rotten egg smell?
The most common cause of smelly water is anaerobic bacteria that exist in some water and react with the magnesium and aluminum sacrificial anodes that come with most water heaters to produce hydrogen sulfide gas, making the classic rotten egg odor.
Does a gas hot water heater have an anode rod?
Inside the Tank In glass-lined tanks, there will be a metal rod in the tank, usually magnesium or aluminum, called a sacrificial anode. The anode rod is bolted and fastened to the top of the tank and extends deep into the tank.
What happens if you don’t replace anode rod?
The anode rod is “self-sacrificing” and will continue to corrode until eventually it must be replaced. When there’s no sacrificial metal left on the anode, the tank can rust out, eventually causing it to burst.
Which anode rod is better aluminum or magnesium?
For harder water an aluminum anode rod is the best choice for your heater and if you live in an area with soft water then a magnesium anode rod is your best choice. Aluminum anodes tend to be cheaper than magnesium anode rods. A magnesium rod will generally last less than an aluminum rod.
Should I replace my 15 year old water heater?
Anyway, you should consider replacing your water heater if it’s about 6-12+ years old and when you start running out of hot water faster. However, age and lack of hot water aren’t everything. You could have a 15-year-old water heater that works just fine and wouldn’t need replacing.
What size socket fits a hot water heater element?
Nearly all hot water heater element wrenches have a 1-1/2 inch hex to fit the standard 1-1/2 inch residential heating element head. In addition, they’re generally at least 5-inches long with cross holes drilled into the opposite end of the pipe so a screwdriver can be inserted for added torque.
What size is the anode rod nut in RV water heater?
I spoke with my Camco contact and the threaded part of anode rod # CAM11563 is 3/4 inches so the hex head is a 1 inch. You would need a 1 inch socket or wrench for installation/removal.
