Table of Contents
Here’s how to replace your fireplace mantel in a few easy steps. Step 1 – Remove the Old Fireplace Mantel. Step 2 – Measure. Step 3 – Purchase a New Fireplace Mantel. Step 4 – Attach the Support Ledger. Step 5 – Prepare the New Mantel. Step 6 – Attach the Mantel to the Support Ledger Board. Step 7 – Secure the Mantel.
How do you remove a fireplace mantel shelf?
Pound the bottom of the mantel shelf with a rubber mallet to separate it from the wall if it doesn’t release when you pry the base of the mantel away from the wall, advises Fireplace Town. Tap it gently, but with enough force to pull the nails from the wall. Once it’s loosened, pull out on the shelf to remove it.
Is it hard to replace fireplace mantel?
A painted wood mantel is the easiest to install. It may need to be shimmed till it’s plumb and level; then it’s fastened to the wall studs with countersunk screws. Most cast-stone mantels arrive in three or four solid pieces (each of which can weigh hundreds of pounds) and are installed with screws or masonry ties.
How expensive is it to replace a fireplace mantel?
The national average materials cost to install a fireplace mantel is $236.47 per mantel, with a range between $212.16 to $260.79. The total price for labor and materials per mantel is $578.11, coming in between $483.53 to $672.69.
How easy is it to change a fireplace surround?
The fire surround is often the easiest place to start, as you don’t need to worry about gas pipes or brickwork. Here, some paint, new accessories or even a whole new surround can go a long way when you need an easy fireplace update.
How do you remove an old mantel?
Place a pry bar along the side of the mantel and tap in place with the hammer if it is a full mantel. Begin at the top edge and pry the mantel off the side of the fireplace. Move the pry bar down the side length of the surround; tap the pry bar in place and pry the side piece off until you’ve removed the entire piece.
How do I remove an old fireplace surround?
To start removing one of these fireplace surrounds, you will have to chip away the plaster around the edge of the mantelpiece. This should reveal the lugs holding it to the wall. You can then go about removing the screws, which should start to release the surround from the wall.
How do you remove the mantel from a brick fireplace?
How to Remove a Mantel From a Brick Wall Remove any decorative trim around the outside edges of the mantel. Insert the short end of an I-beam construction pry bar between the back edge of the mantel and a brick wall. Cut through the mounts with a reciprocating saw to release the mantel.
How are mantels attached?
As with many other forms of mantle or shelf, a fireplace mantel can be commonly attached to the wall with screws or lag bolts. Bolts are screwed into the wall above the fireplace before a mantel is slotted straight onto it. A rubber mallet can also be used to help ease the mantel out of position if it’s stuck.
How far should a fireplace mantel stick out?
A mantel should stick out at least 6 inches (15.24cm) from the wall. It’s the perfect depth that allows you to have a mantle effectively deflect heat without compromising aesthetics. You can extend it to have more depth for your decorative pieces, but we don’t recommend having it less than 6 inches (15.24cm).
How do you hang mantel shelves on brick?
Slide Over Bolts Method Locate the studs behind the brick, stone, or faux veneer. Drive 1/2in lag screws through each of the studs. Have a helper support the mantel while you mark the location of the support rods on the back of the beam. Apply construction adhesive into the holes. Slide into place, admire, and enjoy!.
Can you replace a mantel?
Replacing an older or outdated fireplace mantel can update the look of the entire room. You can expect to complete this project in a few hours, but the pleasure you’ll get from your new mantel will last for years to come. Here’s how to replace your fireplace mantel in a few easy steps.
How much does it cost to install a mantel mount?
Cost to Install a Fireplace Mantel Item details Qty High Unused Minimum Labor Balance of 2 hr(s) minimum labor charge that can be applied to other tasks. 0.0 h $0 Totals – Cost To Install Fireplace Mantel 1 EA $824 Average Cost per Mantel $824.37.
How much does it cost to install a mantel?
Cost to Install a Fireplace Mantel Fireplace Mantel Costs Zip Code Basic Best Fireplace Mantel – Installation Cost $150.25 – $175.35 $250.00 – $390.00 Fireplace Mantel – Total $435.25 – $525.35 $1200.00 – $1490.00 Fireplace Mantel – Total Average Cost per Lineal Foot $480.30 $1345.00.
How do you update a fireplace on a budget?
Learning to DIY: How to Update a Fireplace on a Budget Add a touch of paint. Gone are the days of design elements such as bold and bright red fireplaces and natural, oak-colored wall paneling and trim. Turn your brick to stone. Add a mantel. Think — and build — outside the box. Accessorize, accessorize, accessorize.
How do you remove a fireplace insert?
Step 1: Remove the Trim. Using a hammer, mallet, or pry bar, you will want to remove the trim and any nails around the fireplace that is holding the insert in place. Step 2: Disassemble pipes and Vents. This is the step where you are disconnecting everything. Step 3: Pry the Insert. Step 4: Set it off to the Side.
Can you remove a raised hearth?
You can get rid of the raised hearth, but remember that code requires at least 18″ of non combusitble material in front of the opening (requirements could be more depending on the jurisdiction and size of the firebox oepning) so you will have to put in a new hearth at floor level.
