Table of Contents
On the Categories screen, tap Sensors & Zones. On the Sensors & Zones screen, tap Delete Sensor. Enter the Premise Passphrase and tap Done. Tap the sensor you want to delete, then tap Yes to confirm.
How do you remove a window alarm sensor?
One way on how to disable window alarm sensors is to open the door or window in tiny increments. Once the button is visible, but still engaged, use a Popsicle stick to hold the button down, keeping the alarm from setting off. You can also use sturdy card stock for sensitive alarms.
How do I reset my Xfinity security sensor?
Reset the Motion Sensor Press the bottom of the face and push up to remove the sensor from the battery cover. Remove both batteries from the motion detector. While holding down the tamper switch (C), insert one battery into the motion detector. Release the tamper switch after one to two seconds.
How do you disable motion sensors?
Turn off the motion detector. You can either do this by removing the batteries or just turning the switch off. If you are using a PIR, disconnect the red, yellow, and black wires from the control panel. Using your screwdriver, unmount the device from the wall.
Does Xfinity Home have glass break sensors?
Between those partnerships and its own products, Xfinity is able to offer a pretty comprehensive selection of home security devices. The company has even added glass break detectors as an add-on option since our last review.
What is xfinity motion sensor?
An Xfinity Home motion sensor detects unexpected motion in large sections of your home while you’re away. Set rules to get real-time alerts or trigger other connected devices, like lighting when activity is detected.
What is a PIM sensor Xfinity?
OpenHome Converge Panel Interface Module (PIM) is a professional state-of-the-art device that allows you to manage your wired system and its sensors from your TouchScreen.
How do you remove a wired alarm sensor?
Complete the following steps to remove a wired recessed sensor: Pull out the sensor and its magnet. Pull out both the sensor and its magnet from their respective holes. Disconnect the wire. At the sensor, disconnect the wire from the back of it. Pull out the wire. Complete the removal.
Why does my Xfinity alarm keep beeping?
The device makes beeping noises when arming and will beep faster as your security system gets closer to its armed state. Beeping will stop when the system is armed.
How do I test my Comcast motion sensor?
Motion Sensors Make sure your system is disarmed. Use the touchscreen to bypass the Motion Sensor. Make sure there is no movement in the area for two minutes. Walk in front of the Sensor, then check your system activity in the Xfinity Home app to see if the motion event was detected.
How do I bypass my Comcast alarm?
Bypassing Sensors Tap the Sensor Open message. Tap the open sensor. Uncheck the Sensor is on box. Warning: The alarm will not sound if this sensor is triggered. Return to the Overview screen. The system is ready to arm. Remember – the sensor will stay bypassed until you turn it back on.
How do you turn off a motion sensor switch?
The only way to turn off the override function is to turn the switch off and wait for 30 seconds to 1 minute before you turn it on again. This should reset the sensor so that it works on motion detection again.
Can I add my own camera to Xfinity Home security?
Yes, Xfinity installs security cameras like their indoor/ outdoor camera. However, you can also install it yourself if you don’t want to pay for professional installation.
Can you use your own cameras with Xfinity Home?
Xfinity Home Security lets you own the camera so that you can use it without Service. Disconnect and Reset all the devices in the Xfinity Network and hook it up to your new local network to start using it without service.
How do I add sensors to Xfinity Home?
On the Sensor & Zones screen, tap Add a Sensor/Zone. On the Locating Wireless Sensor screen, do the following, then tap Next. Put the sensor in pairing mode by placing the sensor face down and removing the plastic battery tab.
What does motion sensor Open mean?
Active Sensors When there is an interference caused by a person or moving object, the sensor sends a signal. The signal causes the sensor alarm to sound, a light to illuminate, or even a door to open.
What is the difference between ARM stay and ARM night?
Arm Night is exactly the same as Arm Stay. The only difference is that any Interior Zones with the Arm Night setting enabled will not be bypassed when the system is set to Arm Night mode. Please note that you will only see the Arm Night option if you have at least one sensor with the Arm Night option enabled.
What does bypass mean on Xfinity alarm?
If you bypass a Sensor, it won’t trigger an alarm when the system is armed. For example, if you bypass the side door Sensor and then arm your system, someone entering through the side door won’t trigger an alarm. Enter your keypad code. An entry/exit door must open and close during this period.
Do motion detectors have batteries?
The motion detector requires one CR123A 3 volt battery. This battery can be purchased at your local hardware, mass retailer or battery store. Some models may require two batteries. Before you replace the battery, put your system into test mode to prevent false alarms.
