Table of Contents
To fix well water that smells bad, use one of these approaches: Aerate water and/or inject air or oxygen. Chlorinate well water to eliminate both sulfur and bacteria. Use ozone gas in a closed tank or atmospheric tank. Inject hydrogen peroxide.
How do you get the smell out of well water?
Use a Chlorinator or Inject Hydrogen Peroxide to Kill Odors J-PRO Odor Killer Well Water Chlorinators Eliminate Both Odors and Odor-Causing Bacteria in your well water. Use 5% grade liquid bleach or 12% liquid pool chlorine OR 7% hydrogen peroxide. The same system can inject either bleach or peroxide.
How do you get the sulfur smell out of well water?
Chlorine bleach can effectively remove medium to high levels (over 6 mg/l) of hydrogen sulfide. The chlorine in the bleach chemically reacts with (oxi- dizes) the hydrogen sulfide eliminating the “rotten egg” odor. Chlorine bleach also reacts with iron or manganese, and disinfects water supplies.
Why does my well water stink?
Hydrogen sulfide gas, which smells like rotten eggs, may occur naturally in well water. Less commonly, it could be due to a direct source of pollution. Most frequently, however, the smell of sulfur in your water is likely due to the existence of sulfate-reducing bacteria, which produces hydrogen sulfide as a byproduct.
Is it safe to drink well water that smells like sulfur?
In most cases drinking water that has a strong rotten egg odor, although particularly unpleasant, is perfectly safe to drink. However in some rare occasions the odor may be caused by sewage or other contaminates in a building’s water supply, which could cause health problems.
Can I pour bleach down my well?
Mix 2 quarts bleach in 10 gallons of water; pour into well. Connect a garden hose to a nearby faucet and wash down the inside of the well. Open each faucet and let the water run until a strong chlorine odor is detected, then turn it off and go to the next one. Pour it into the well without pumping.
Can you put bleach in well water?
Mix the bleach with the well water. Ⅰ Attach a hose to the nearest outside faucet and allow the water to run onto the ground for 1-2 minutes until you smell chlorine. Then place the hose in the hole where you poured the bleach, allow the water to run back into the well for 15-20 minutes.
How do you neutralize the smell of sulfur?
Baking soda is well known for erasing odours. And the best thing is that it’s very easy to use and efficient too. If the smell is coming from your clothes then, soak them in baking soda before washing. You can also sprinkle baking soda in all the corners of your house to get rid of the sulphur scent.
How do you fix rotten egg smell in hot water?
To get rid of the bad odor, you’ll want to contact a plumber to flush and disinfect your tank. Doing so will remove the bacteria and particles that create hydrogen sulfide. During a water heater flush, a plumber can replace your anode rod if it is corroded to prevent the smell in the future.
Will a water filter remove sulfur smell?
Regardless of the source of the odors, installing whole house water filters that will remove hydrogen sulfide and kill sulfur bacteria is a good solution to consider if you want to reduce bad smells, and protect your family from other chemical and microbial contaminants.
How do I chlorinate my well?
Overview. Use ordinary liquid laundry bleach to shock chlorinate the water system. Determine how much bleach to use, then pour the bleach down the well and circulate it through the whole water distribution system. Wait 6-12 hours for the chlorine to work, then flush the chlorinated water from your well and pipes.
How much bleach should I put in my well?
4) Work out how much bleach will be needed: For every 50 gallons of water in the well use one quart of laundry bleach – (4 quarts in a gallon). Do not use excessive amounts of bleach – more is not more effective. 5) For best results the bleach should be combined with water before adding it to the well.
Will a carbon filter remove sulfur smell?
Activated carbon filters at the tap or for the entire house can remove small amounts of hydrogen sulfide, so these are best for water in which the sulfur smell isn’t too strong.
Why does my well water smell Swampy?
There are two types of bacteria that cause odors: sulfur- oxidizing and sulfur- reducing. Some sulfur bacteria form deposits that can clog a well screen and pump piping. Sulfur bacteria samples are difficult to collect and take a long time to analyze. You may wish to have your water tested for iron bacteria instead.
Is it OK to shower in sulfur water?
It’s perfectly safe to shower in sulfur water. Doing so won’t endanger your health or wellbeing. Having said that, the presence of sulfur water in your plumbing might cause it to rust or corrode over time. Especially if the sulfur water contains high amounts of hydrogen sulfide.
How do you get the iron smell out of well water?
To solve this, change the anode rod to an aluminum rod. Even if there’s no odor in the cold water but the hot water smells like rotten eggs, then you can also add a pint of store-bought hydrogen peroxide to the water heater and let it sit for 4 – 6 hours. This will often kill the odor for weeks or months.
Can I put a chlorine tablet in my well?
the well has been flooded or exposed to bacterial contamination in another manner, such as a crack in the well cap. Chlorine granules, tablets and liquid chlorine in the form of household bleach can all be used to disinfect your well.
How do I disinfect my well?
Rinse the inside of the well casing with a garden hose or bucket for 5-10 minutes. Open all faucets inside the home and run the water until you notice a strong odor of chlorine (bleach) at each faucet. Turn off all faucets and allow the solution to remain in the well and plumbing for a minimum of 12 hours.
