Table of Contents
To remove the ecobee backplate, carefully remove your thermostat from the backplate by putting your thumb and index finger on the backplate. Then, pull against the ecobee3 lite. Remove the screws from the backplate to remove it from the wall.
How do I remove the ecobee sensor?
ecobee Room Sensors use 3-volt CR-2032 batteries that can be purchased here. If your sensor uses the sensor stand: Place your thumb and index finger on the narrow part of the sensor stand, and your other hand on the front of the sensor. Gently pull upwards to release the sensor.
How do you attach ecobee sensor to wall?
There are two ways that you can place the sensor: mount it on a wall or place it on a flat surface. If you are placing your room sensor on a wall: Place on a flat surface using the stand provided. Make sure it is facing the room, instead of the wall Place it at a height of approximately 5ft / 1.5m on an interior wall.
Where is the ecobee sensor?
To view remote sensors connected to your ecobee thermostats, navigate into a building with thermostats, click a thermostat with paired sensors, and scroll down. You can check on the temperature and occupancy status of your sensors, and if it is a monitoring only, control, or participating sensor.
How many ecobee sensors are needed?
ecobee thermostats can accommodate up to 32 sensors.
Does the ecobee thermostat count as a sensor?
ecobee room sensors are an additional accessory that you can pair with your ecobee smart thermostat which allows the thermostat to know the temperature of different rooms in your house. Not only do the room sensors detect temperature, but they also have motion sensors so it can tell when somebody is in that room.
Do Ecobees have batteries?
1 Battery Replacement Your ecobee room sensor is powered by a single 3 Volt CR-2032 battery.
How do I remove the battery from my ecobee sensor?
Change the Battery Place your thumb and index finger on the narrow part of the sensor stand, and your other hand on the front of the sensor. Gently pull upwards to release the sensor. Remove the battery by gently prying it out of the battery compartment with a thin tool such as a pen, plastic card, or screwdriver.
How long does ecobee sensor stay occupied?
When you leave that room, the sensor will remain occupied for 30 minutes. This means that if you are moving around the house, the thermostat won’t be continually turning on and off. After 30 minutes of no movement, the sensor will become unoccupied. It will stay unoccupied until movement is detected again.
How do I calibrate my ecobee sensor?
To Configure Temperature Correction Press Menu on the main screen. Go to Settings. Then go to Installation Settings. Select Thresholds. Then select Temperature Correction. Adjust the temperature reading to fit your needs.
How do ecobee door sensors work?
Ecobee SmartSensors for doors + windows They work much like other door and window sensors; you align the base sensor with its corresponding magnet, and you can monitor when a door or window is open or closed, as well as when motion is detected.
Do Ecobees communicate with each other?
Many people ask if it possible to sync two Ecobee thermostats. According to the developers, yes, it is possible to sync multiple Ecobee devices to each other. All Ecobee devices are interconnected and they are compatible with each other.
Does ecobee Smart sensor measure humidity?
The humidity sensor in the Ecobee Smart Thermostat senses the humidity in the house and adjusts the temperature as needed to make sure it feels how you want it to in your home.
Which ecobee is best?
Best ecobee Thermostats in 2021 The flagship: ecobee SmartThermostat. Less expensive, fewer perks: ecobee3 lite. Essential and convenient: ecobee Switch+ Must-have accessory: ecobee SmartSensor (2-pack).
Does ecobee work without electricity?
The only batter that’s in the ecobee 3 thermostat is to back-up the data and you will not be able to access is unless you take the thermostat apart. In the case of a power outage, once power is restored the battery has retained all in the information such as scheduling, etc.
How do I contact ecobee?
Need to talk? Contact Us. Send us a message. Toll Free. 1-877-932-6233. International. 1-647-428-2220. Security team. If you’re a security researcher, please use our public PGP key when sending us sensitive information. We take security very seriously and investigate all reported vulnerabilities. Email: security@ecobee.com.
How do I check the battery level on my ecobee sensor?
You cannot check your Ecobee sensor’s battery level, but Ecobee will notify you through the app when the battery life is running low.Here are the steps: Pry the cover off the back of the sensor. Remove the old battery from the sensor. Insert a new battery with the positive side facing out.
Why is my ecobee beeping?
An Ecobee thermostat beeping is likely due to unread notifications from Alexa or a similar app. Reading or deleting the notification is the best way to get rid of the noise. If the sound persists, it may be due to electrical faults or coming from external sources outside the thermostat.
Can you turn off ecobee motion sensor?
To Toggle the Thermostat’s Sensor Press Menu on the main screen. Go to Sensors. Check or uncheck the Comfort Setting for which you want or don’t want to use the sensor.
How does ecobee sensor know a room is occupied?
The sensors include a motion detector to tell the ecobee which parts of your house are active. The motion sensors are passive infrared motion sensors. This means they use the natural infrared radiation given off by all objects as a means of detecting motion, and therefore work regardless of light or dark.
How do I make my ecobee sensor occupied?
Tap and hold your finger on the number to the right and drag it to set the desired indoor temperature that you want your thermostat set at when you’re not at home. Then hit “Save” in the bottom-right corner. Do the same thing for the heating temperature if you have the heat running.
Is the ecobee sensor accurate?
The ecobee temperature sensor has a +/- 1.0F accuracy and is programmed to provide readings every 15 seconds. It will use the previous two values and average them into the current reading.
Does ecobee need to be calibrated?
The Ecobee thermostat requires calibration to get an exact reading of the room temperature which takes around 20 minutes. Note-Remember not to use AC or heater during your ecobee calibrates.
What is ecobee temperature correction?
If the thermostat reading needs adjusting for any reason, there’s a Temperature Correction function which will permanently correct the sensor reading by +/- 10F in both directions.
