Table of Contents
Remove the Bathtub Drain Stopper Set the drain to its open position. Lift up on the drain stopper’s knob and turn it counterclockwise. After enough turns, the drain stopper should be unscrewed and come free from the drain opening.
How do you remove a push pull drain stopper?
To remove a push-pull stopper, set it in the open position and turn the knob counterclockwise with one hand while holding the body of the stopper in the other. For increased leverage, hold onto the body with a towel and use a pair of pliers to turn the knob. For the lift-and-turn, set the drain to open.
How do you remove a lift and turn stopper without a screw?
If there is no set screw on either the knob or the stopper, it likely uses a channel/pin mechanism. Lifting the stopper, slowly rotate it counter-clockwise, aligning the slot at the bottom of the channel with the pin on the strainer. Pull upwards to release the stopper.
What are the different types of bathtub drain stoppers?
The most common types of bathtub drain stoppers are lift-and-turn, push-and-pull, pop-up, toe-touch, flip-it, and trip lever. Identifying which type you have will help you when it becomes necessary to fix or replace your drain stopper.
What can I use if I don’t have a drain wrench?
Short of a plug wrench, the best substitute is a set of needle-nose locking pliers. The pliers need to be small enough to reach into the drain and through the cross. Once the locking pliers are secured, you use a pair of standard pliers to turn the locking pliers and loosen the drain.
Are all bathtub drains the same size?
Bathtub drains are 1 1/2 inches wide and fit all standard bathtubs ranging from 14 to 26 inches deep. They are this size because they must fit the opening of the P-trap — also 1 1/2 inches wide — which is a special pipe that has a sharp bend in it.
How do you measure a bathtub drain stopper?
Measure straight down from the center of the overflow to the point at which the drain is mounted to the tub: depending on what’s easiest to get to, you can measure from outside the tub down to its underside, or from inside the tub to the tub floor.
Do you need a drain wrench?
Remove the Drain Basket Once you have removed the drain stopper, you will see the drain basket (also known as a drain flange) in the drain opening. The drain basket will have a metal crossbar at the bottom. To remove the drain basket, you will need either locking pliers or a tub drain wrench.
What is the best tool to unclog a tub drain?
A plunger is one of the most popular tools to prevent bathtub clogging. How successful you are will depend on the nature of the clog as well as the design and size of your drain. Take a plunger and add some water to the tub before you start to plunger vigorously.
How do you remove a Kohler bathtub drain?
How do you get them off? Lift the stopper part way up (all the way up and it spins around freely; part way up and it will not turn, providing the “resistance” for you to screw against) and then turn it counter-clockwise. This will unscrew the stopper from the rod that connects it to the drain.
How do you remove an old shower drain flange?
REMOVAL OF EXISTING SHOWER DRAIN BODY Remove drain cover with flat blade screwdriver. Remove the crown nut by unthreading it using needle nose pliers. Extract the compression seal exposing drain pipe and shower drain body. With mini hacksaw, make two vertical cuts approximately 1” apart through drain body.
How do you remove a shower drain cover UK?
Use the flat-head screwdriver to pop the drain cover out of the drain fixture. Place the tip of the screwdriver along the edge of the drain cover, not outside the actual drain fixture. Locate a screw in the centre of the cover. Use the flat-head screwdriver to pop the drain cover out of the drain fixture.
What size is the bath waste pipe?
There are four basic sizes of plastic waste pipe for different plumbing uses. The hand basin waste pipe is 32mm. 40mm is for sink and bath waste pipe.
How do I choose a bathtub drain?
When it comes to selecting a bathtub drain finish, look for a finish that will coordinate with the other finishes in the bathroom. It should complement the colors and finishes already chosen, from the sink faucet and vanity hardware, to the tub faucet and shower system.
What size pipe is used for tub drain?
The actual drain pipe that’s in the slab the plumber will connect to is probably 1 1/2-inch diameter. That’s a common pipe size for tubs. Large stand-up shower stalls tend to have 2-inch pipes draining them.
Why won’t my pop up plug stay down?
Adjust the nut. If the stopper moves as it should but doesn’t stay put, all you need to do is tighten the nut (turn it clockwise). If the action is too stiff, loosen the nut a little. Check the action and adjust until it feels about right.
How is drain diameter measured?
How to Measure a Sink Drain Opening for a Crumb Cup Measure the drain opening across its widest part. This gives you the diameter of the drain circle. Insert the end of the measuring tape into the drain, beside the edge. Note the measurements on a piece of paper and take them with you when you shop for a crumb cup.
What do professional plumbers use to unclog drains?
Hydro-Jet For the toughest of clogs, a plumber may use a hydro jet. This tool sends pressured water through pipes to break down drain build-up. This tool is often faster and more efficient than a typical drain snake. Hydro jets get rid of the clog, but they’re also effective for cleaning drains.
How do you remove a drain flange?
If you’re removing the entire drain apparatus, including the basket (also known as the flange), insert your drain key or smart dumbbell into the opening. Turn it counterclockwise and continue turning until the drain flange is released, then remove the flange while it’s still attached to the drain key.
What is a tub flange?
“What is a tub flange?” It’s a “raised rim” around the edges of the tub that will sit against the shower walls.
How do you snake a bathtub drain without a snake?
Put in your drain stopper, turn on the hot water and let it pool in the sink. Add one cup of baking soda and two cups of vinegar to the water and remove the stopper. The hot water, baking soda, and vinegar will flow down the pipes and help eliminate minor clogs.
