Table of Contents
Is there a tool to remove a bathtub drain?
If your drain doesn’t have crossbars, you’ll need to use a tool called a tub drain extractor. It has a conical shape and helical knurls that grip the metal wall on the inside of the drain fitting. You turn the extractor with an adjustable wrench.
How do you remove a built in drain?
Set the drain to its open position. Unscrew the knob on the top of the drain stopper to see if there is a set-screw underneath. If your drain stopper has a set-screw, use a small screwdriver or a hex key to unscrew it. Twist the entire stopper counterclockwise until it pulls free from its mounting post.
How do you remove tub drain with pliers?
To remove a push-pull stopper, set it in the open position and turn the knob counterclockwise with one hand while holding the body of the stopper in the other. For increased leverage, hold onto the body with a towel and use a pair of pliers to turn the knob. For the lift-and-turn, set the drain to open.
How do you remove a PresFlo stopper?
A PresFlo stopper doesn’t have a knob, and it rotates in the drain opening rather than lifting. The only thing holding it in the drain opening is the O-ring around its perimeter, and you can often remove it by pulling it out with your fingers after opening the drain.
What are the different types of bathtub drain stoppers?
The most common types of bathtub drain stoppers are lift-and-turn, push-and-pull, pop-up, toe-touch, flip-it, and trip lever. Identifying which type you have will help you when it becomes necessary to fix or replace your drain stopper.
Are all tub drains the same size?
According to Bonnets Stems and Accessories, Inc., a standard modern bathtub drain is 1 1/2 inches in diameter – the width straight across the middle. Antique bathtubs, such as historic clawfoot tubs, sometimes have slightly smaller drain openings, often 1 3/8 inches in diameter.
How do you use a drain tool?
The basic process is as follows: Push the end of the snake into the drain opening and turn the handle on the drum that contains the coiled-up snake. Keep pushing more of the snake into the drain until you feel resistance. Rotate the snake against the blockage until you feel it feed freely into the pipe.
How do you remove shower drain cover screws?
Hold the stopper body in place and unscrew the top knob (counterclockwise) with pliers and a rag or rubber grippy to prevent scratching. Unscrew the brass insert beneath with a flathead, then lift the stopper. From the open position, lift and look for a set screw. If no screw, simply turn counterclockwise to remove.
What are the different types of shower drains?
The Types of Shower Drains [7 Types and Styles] Point Drains. Linear Drains. Decorative Drain or Hidden Drain. Single-Piece Drain. Multi-Piece Shower Drain. Shower Drain Finish and Style. Tileable Drain Grate.
What is a tub drain assembly?
A bathtub drain flange is the finished drain part that’s visible in the tub. A rubber gasket underneath the tub seals the drain elbow to the tub. That drain elbow connects to a length of pipe that then connects to the waste and overflow pipe.
How do you get a push plug out?
With a cup, scoop out the contents of the sink. This’ll make it easier to get to the plug. With a rubber glove on, push down on the plug and attempt to twist it anti clockwise. If that doesn’t work, spray WD-40 on to the plug, give it a minute to work itself under the plug, then repeat step 2.
How do you measure a bathtub drain stopper?
Measure straight down from the center of the overflow to the point at which the drain is mounted to the tub: depending on what’s easiest to get to, you can measure from outside the tub down to its underside, or from inside the tub to the tub floor.
Are bath plugs a standard size?
Standard bath plugs measure about 1-3/4 inch (44.5mm) diameter and suit the hole in a 1-1/2 inch BSP waste. If your original bath plug is a pop-up type, be careful with the replacement as pop-up plugs are often a non standard size.
Are bathtub drains universal?
Bathtub drains are 1 1/2 inches wide and fit all standard bathtubs ranging from 14 to 26 inches deep.
How do I choose a bathtub drain?
When it comes to selecting a bathtub drain finish, look for a finish that will coordinate with the other finishes in the bathroom. It should complement the colors and finishes already chosen, from the sink faucet and vanity hardware, to the tub faucet and shower system.
What size pipe is used for tub drain?
The actual drain pipe that’s in the slab the plumber will connect to is probably 1 1/2-inch diameter. That’s a common pipe size for tubs. Large stand-up shower stalls tend to have 2-inch pipes draining them.
What size thread is a tub drain?
The inside diameter of the 1st thread of a 1-1/4″ drain, which is the next standard U.S. size down from 1-1/2″ will be approximately 1.6″, or about 1-5/8″. The 1-1/2″ size should be standard for U. S. bathtub drains.
How do plumbers unclog drains?
The plumber inserts the hose deep down into the drain, and then high-pressure water blasts out the nozzle to clean out all parts of the drain. The pressure is enough to completely wash away all debris clinging to the drainpipe walls, making it hard for debris to build up again.
How do you snake an outside drain?
Overview of Steps Locate and clean around the outside of the cleanout plug to keep leaves and dirt from falling into it. Place the root cutting head of the auger in the cleanout access and turn on auger’s power. Feed the auger cable into the drain until resistance can be felt as it meets and begins to cut at roots.
