Table of Contents
How do I remove a urinal?
Put a hex-head key into the hole and turn it clockwise to stop the water flow to the urinal. Flush the urinal with the handle several times to verify the water is not running. Loosen the fittings on both sides of the flush handle using the pipe wrench, then take them off by hand and remove the valve.
How is a urinal attached to the wall?
The urinal is attached to the wall at the top with hangers that are screwed to the wall. The bottom is attached with lag screws through the slots in the china, through the holes in the outlet connection, into the finished wall. Dimension “A” is the centerline location of the primary hanger mounting screws.
What is at the bottom of a urinal?
They’re called “urinal cakes” and are commonly seen at the bottom of urinals. Their purpose? Control bacteria and reduce smell. They’re made of para-dichlorobenzene, a chemical that does deodorize but comes with baggage.
Do urinals have wax rings?
Urinal wax rings, seals, and gaskets help form water-tight connections to prevent leaks around urinals. They seal the connection between the urinal and flush valve or between the urinal and the wall or floor.
Does a urinal need a trap?
Do Urinals Have Built-In Traps? Yes, some models and types of urinals do come with built-in traps that play a very important role in the entire process. For instance, a standard urinal has a pipe known as a “P-trap” where all the water is flushed into it by the urinal.
Does a urinal need to be vented?
No, each urinal will most likely need its own vent. In some places you may be able to use a double fixture fitting and vent 2 off the double fitting. You cannot, however, simply put 1 vent at the end of the last fixture.
How much does it cost to install a urinal?
1.6 gallons of water per flush, and a urinal about 1.8.” The cost of the equipment and installation makes it a tough sell, also. Kyle Hokel, a Sanitary Product Engineer for toilet king Kohler, tells us urinal prices range from $200 to $2000.
How long does it take to install a urinal?
Replacing a toilet is a simple and straightforward job, so you should be able to remove the old toilet and install the new one in about two to three hours. However, if you don’t have a lot of DIY experience, you might want to add an hour or two to that timeframe.
What is a washout urinal?
A wash out or wash down urinals release water through ports in the top of the urinal or on the side of the lower bowl to clean the urinal and remove waste water. In other word, it fills up the water before cycle down.
What size is a urinal drain?
1 1/2 Fixture Minimum Size of Trap & Fixture Drain (Inches) Sink, Soda Fountain or Bar 1 1 / 4 Urinal, Stall 2 Urinal, Trough 1 1 / 2 Urinal, Wall 1 1 / 2.
Why do they put ice in urinals?
To bartender’s surprise, the ice eliminated urinal odors. As one expert explained, the ice froze odor causing molecules in urine, preventing them from being released. Eventually, the odor-filled molecules melt with the ice and drip down the urinal and into the sewer.
Why are there urinals in men’s bathrooms?
In busy public toilets, urinals are installed for efficiency. Consistent use of urinals also keeps the toilet stalls cleaner and more available for males who need to defecate. A urinal takes less space, is simpler, and consumes less water per flush (or even no water at all) than a flush toilet.
Why are there strainers in urinals?
Urinal drains and strainers help prevent clogs by stopping debris from entering waste lines. They have holes that allow liquid to pass through while keeping out large, solid particles. These strainers fit into a drain to filter out debris.
What is a flush valve?
The flush valve, located in the middle of the toilet tank, includes the overflow tube, the hole where water enters the bowl when the toilet is flushed and the rubber tank ball or flapper that covers the hole when the tank is full. A broken flush valve prevents your toilet tank from forming a seal to hold water.
What should you never use to install a Sloan flush valve?
Protect the chrome or special finish of Sloan Flushometers — DO NOT USE toothed tools to install or service these valves. Use a Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth jawed spud wrench to secure all couplings.
How do waterless urinals work?
Waterless urinals divert urine through a one-way valve into a “trap.” This trap contains a chemical that is less dense than urine. When the urine flows through this trap, the liquid displaces the urine, forcing it lower into the trap. As this trap fills up, it diverts urine to a drain connected to a sewer.
What is the minimum distance between urinals?
Between urinals: There should be about 12 inches of space between urinals to allow room for the partition and space for users to stand. Front lip: The front lip of a wall-mounted urinal should be a minimum of 13.5 inches away from the wall and 17 inches from the floor. It should have an elongated rim.
