Table of Contents
You can reboot the Smart Si thermostat by pressing the physical hardware reset button, located through an opening in the bottom left corner of the Smart Si thermostat. Rebooting will not alter programming or configuration options.
How do I reboot my ecobee?
1 Reboot Push and hold the main button on your Ecobee Switch+. Continue to hold the main switch for five seconds. Wait for the voice prompt to say “Restart Device”. Press the main button one time. Your Ecobee Switch+ will restart, and should be ready to use again in a few minutes.
Why is my ecobee thermostat not working?
Open the panel on your furnace to expose the control panel where your thermostat wires are connected. Most systems have a purple 3 or an orange 5 amp fuse on the board—check this fuse to ensure that it’s intact. A blown fuse will have to be replaced. Once a blown fuse is replaced, the ecobee should power back on.
How do I reset my frozen ecobee thermostat?
Reboot Your ecobee Pull the thermostat from its wall mount. Keep the thermostat powered off for a minute then put it back on the wall. Allow the thermostat to complete its boot up process. Place the ecobee back on the wall after one minute and wait for it to reconnect to Wi-Fi.
How do I reset my Ecobee?
Unregister Your Ecobee from the Thermostat Go to your Ecobee Thermostat’s main menu. Hit Settings. Hit Reset. Hit Reset Registration. Confirm and hit Yes.
Does Ecobee thermostat have a battery?
The Ecobee comes with one wireless sensor, which is powered by a CR2032 coin-cell battery; the company says it should last about 4 years. When the battery runs low, you’ll receive an alert.
How do you manually reset ecobee?
1 Factory Reset From the Home screen, press Menu. Select Settings. Go to Reset. Choose Reset All Settings then confirm your selection by pressing Yes. Choose the reset option that suits your needs: The ecobee thermostat will be reset to factory defaults.
Why does my ecobee keep restarting?
There are three reasons why an Ecobee thermostat may be rebooting often: The wiring to the thermostat is damaged, loose, or installed incorrectly. The furnace is overheating. The HVAC unit needs to be cleaned or serviced.
How do I reset my ecobee without access code?
How do I reset my ecobee password? Navigate to the login page on your mobile device, or web browser. Select “Forgot password?” and enter the email address associated with your ecobee account. You should receive an email with a link to reset your password. Once you complete, you will receive a final confirmation email.
How do I restart ecobee after power outage?
Flip the breaker back on. Wait at your breaker box for 30 seconds, to make sure it does not flip back quickly. Allow your thermostat an additional minute to finish starting back up. Try adjusting the temperature to ensure it’s functioning properly.
What causes no power to thermostat?
The power is out or a circuit breaker has tripped If the blank thermostat occurs during the day, it’s possible that you have lost electrical power to your house and haven’t noticed it yet. The power loss could also be the result of a tripped circuit breaker that powers the air conditioner or heater.
What happens if ecobee loses power?
If this power supply is interrupted, the ecobee will not power back on until 24VAC is restored. When the ecobee thermostat loses power during heating or cooling, it is often due to one of the following: A safety feature on the HVAC (Heating, Ventilation, and Cooling) system triggering, cutting power to the thermostat.
How do I reconnect my ecobee to WIFI?
To connect your Ecobee thermostat to your Wi-Fi network: From the Home screen, press Menu. Then select Settings. Go to Wi-Fi. Make sure Wi-Fi Radio is Enabled. Go to Network. Tap on Select Wi-Fi Network. Pick your Wi-Fi network from the list and enter your Wi-Fi password if required. Tap OK to exit.
How do I reconnect my ecobee sensor after changing the battery?
Place your ecobee thermostat back on the wall and wait for it to power up. Place the battery back in the sensor and the battery cover or sensor stand onto the battery slot. You should now receive a prompt on your ecobee’s screen to pair the sensor.
How long does ecobee battery last?
CR2032 are the little silver coin shaped batteries used in the old ecobee Room sensors. The sensor will run for at least 18 months. The CR2477 used in the new Smart Sensors should last for five years.
Why does my ecobee keep running?
This is a common problem with Ecobee and other smart thermostat systems. If this setting isn’t switched to “auto,” your fan could be stuck running all the time. With the fan in “auto” your system is going to automatically run the fan whenever it needs to adjust the temperature of your home.
Why does my ecobee keep going offline?
If your ecobee is connected to your home network but is unable to connect to ecobee servers, the issue may be caused by security settings on your router. To check if your ecobee is connected to ecobee servers, go to MAIN MENU > ABOUT > WI-FI > CONNECTED TO ECOBEE.COM.
How long does an Ecobee thermostat last?
Ecobee states a battery life of 5 years (you can replace it yourself, when the time comes) and claims it’s smart enough to not be triggered by pets.
How do I find my 4 digit ecobee code?
This code is obtained by doing the following on your ecobee thermostat’s screen: 1. Tap the three horizontal bars on the bottom left corner of the ecobee screen to open the Main Menu. After completing these steps, the code will then be displayed on the thermostat’s screen.
