Table of Contents
What does the Code F mean on a Whirlpool washer?
Whirlpool Cabrio washers will display a variety of error codes whenever there is a problem with the washer. An F error code usually means the washer will not work at all, and the control board will need to be replaced.
What is F28 on Whirlpool washer?
The digital display on the Whirlpool Duet washer, at times, will display an error code to alert you of a problem with the washer. An F28 error code is a common problem that means there is a communication problem with the central control unit. This problem is generally solved by essentially rebooting the control unit.
Can you reset a Whirlpool washing machine?
Turn off the washer on the control panel. Unplug the washer for twenty seconds. Turn on the washer. If the process has worked, your washer will now be reset.
Is there a way to reset a Whirlpool washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
What does F09 mean on a Whirlpool washing machine?
Accepted Answer. Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.
What does F11 mean on Whirlpool washer?
The F11 error code in the Whirlpool washer reports about the engine control board malfunction. Having found out this, a user will immediately adhere to household appliance repair specialists.
What is the F5 code on a Whirlpool washer?
The “F5” error means that the temperature sensor has recorded an unusual reading while using hot water. This usually is a sensor error rather than a malfunction of your hot water heater.
What does F3 mean on a Whirlpool washer?
If the washer is displaying error code F3, the washer has detected a water supply issue or an internal problem. F03. There may be a problem with the pump or pressure switch, attempt a Hard Reset. Hard Reset. In some cases the control can be non-functioning or may not accept activation from the control panel.
What does error code F28 mean?
Posted: Aug 1, 2017. shantapanchu a F28 error code is a common problem indicating that there is a communication problem with the central control unit. Any error code can be caused by a electrical anomaly. try to reset your washer. This reset might work but will depend on your specific model.
Why does my washer say F 28?
F28 means that your main central control board (CCU) and the motor control board (MCU) are not communicating with one another properly. You will need to check all the connections at both boards, the mcu is in the bottom of the washer and the ccu is mounted at the top inside of the washer on the right side.
What is a F21 error on Whirlpool washer?
If your Whirlpool washer has an F21 error code, it indicates that your washer has a drainage problem. The good news is the issue can usually be resolved by simply clearing the drain filter or drain hose.
How do I reset my Whirlpool Cabrio Top load washer?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
How do I reset my Whirlpool load and go?
Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Does unplugging a washer reset it?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
What is error F09?
The Whirlpool Duet Washer F09 Error is a overflow condition error. It means the overflow contacts on the water level pressure switch have been closed for more than 60 seconds. If the pump is running but the washer is not draining check the tub to pump hose and the drain hose for blockage.
What is code F9 and E1 on Whirlpool washer?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. Lower drain hose if the end is higher than 96″ (2.4 m) above the floor. Remove any clogs from drain hose.
What does E03 mean on a washing machine?
An E03 error code means that your washing machine has encountered a draining problem.
How do I fix the F11 code on my Whirlpool Duet washer?
To Fix Whirlpool Duet Washer F11 Error Code the first thing you need to do is check the wiring and connection between the central control unit and the motor control unit. Disconnect the wire at the central control unit from the motor control.
What does f1 mean on a Whirlpool Duet washer?
The F01 error on this model washer means the relay for the drain pump motor on the main control board (CCU) has failed to activate or a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU occurred.
