Table of Contents
Which way does the wax ring go on the toilet?
How to use wax when installing a toilet bowl Clean surfaces on underside of toilet bowl and floor flange of old wax and debris. Remove old floor bolts, and place new bolts secure with the retainer washer. Press wax ring on bowl outlet with plastic flange pointing away from the bowl.
Do I put the wax ring on the toilet or the flange?
Place the wax ring on the closet flange, not on the toilet. Pick up the toilet and set it evenly over the closet flange, making sure the bolts come through the bolt holes in the toilet base. Fine-tune the toilet position, so it’s right where you want it, then push it straight down so it smashes the wax evenly.
Can I use 2 wax rings on toilet?
You can certainly install a toilet with multiple wax rings, in fact sometimes it is necessary to make sure you don’t have a leak. You can buy an extra-thick wax ring, or you can just buy two rings and stack one on top of the other.
How often should you change the wax ring on a toilet?
Between the toilet and the flange is a wax seal. The wax keeps water from leaking as it passes from the toilet to the drain pipe. It also seals against foul sewer gas odors. A wax seal will often last the life of the toilet, 20 or 30 years, without needing to be changed.
Does the toilet flange sit on top of tile?
Yes, the toilet flange should be seated over the tile so that it can be secured tightly through the bolts. The usual method followed is to place the flange on the tile and its bottom is touching the tile. You then fix the flange with the screws ensuring they go below the thickness of the tile.
Should toilet flange be flush with floor?
The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too.
Which is better wax or rubber toilet seal?
Using a wax-free seal makes clean up easier and there’s less room for error. If you need to remove the toilet base with a wax ring, you’ll need to purchase another ring to reinstall the toilet. When you use a wax-free seal, it’s reusable as long as it’s in good condition.
Why does toilet wax ring leak?
A: The most likely cause is that the wax ring around the closet flange is leaking, allowing a small amount of water to seep from under the toilet with each flush. The wax rings are probably misaligned. The fix is to reseat the toilet using a flange extension and one wax ring.
How do I know if my toilet wax ring is bad?
The telltale sign of wax ring failure is water leaking out from around the base of the toilet. You might also notice a toilet feeling unusually wobbly if the wax ring is coming loose.
How do you put two wax rings on a toilet?
How do you install a 2 wax ring on a toilet? Turn off your water supply after you empty the tank and the bowl. Unscrew the bolts and gently pull the toilet up. Remove the existing wax ring by using a putty knife. You will then need two wax rings (one with an attached plastic pipe extension and one without).
Can you stack toilet flange spacers?
The four individual spacers can be stacked to any height or can be snapped in half to support an existing closet flange.
When should you use an extra thick wax ring?
If it’s at the same level, or no more than 1/4 inch below it, a regular wax ring, which is between 3/4 and 1 inch thick, is all you need. If the flange is recessed deeper than that, you need an extra-thick wax ring, which is about an inch thicker than a regular one.
Will bad wax ring cause toilet not to flush?
Sometimes when there is a clog, the bowl does not refill after the flush, of if there is paper left in the bowl the bowl may slowly siphon dry over time. If this is not happening, you cannot get sewer gas through the toilet. A bad wax ring can be the culprit.
Do you need to remove old wax ring?
When should you consider replacing your wax ring? Here are a few times when replacement may be necessary: If you have to remove your toilet for any reason, you should plan to replace your wax ring. Lifting the toilet will break the seal and if the wax is old, it may not reseal.
How much does it cost to replace a wax ring on a toilet?
Replacing a wax ring, also referred to as a wax seal, will run between $50 and $200, including labor and materials. While the ring itself is inexpensive at $2 to $10, replacing it takes time and expertise. The closest flange may also need replacing, which can increase total project price.
How do I fill the gap between my toilet and floor?
Apply a thin, even bead of caulk around the base of the toilet to cover the gap along the floor and hide the shims. If necessary, smooth the caulk with your finger, wiping your finger clean frequently with a paper towel or a rag.
Can plunging a toilet damage the wax ring?
Plunging down too hard In an effort to dislodge whatever is clogging the toilet, many homeowners get overzealous and thrust too hard downward into the toilet with their plunger. A hard thrust downward can break the wax seal between the toilet and the floor, causing a leak.
How far should toilet flange be from tile?
Most toilets have the flange above the flooring, roughly 1/8th to 1/4th of an inch above the tiles.
