Table of Contents
How do you support a closet rod?
Before installing a closet rod, it is best to place closet brackets in a position on the wall that allows for the most support. This will require a stud finder. Once wall studs have been located, closet rods and brackets can be screwed into the stud for optimal support.
How do you hang a closet rod and shelf?
How long can closet rods go without support?
If your closet rod is longer than 48 inches, you will need support. However, regardless of how long the closet rod is, if you’re hanging heavier items such as winter jackets, then you will want support no matter what.
How do you hang a closet rod from the ceiling?
Draw a straight line on the ceiling at right angles to the joists using a yardstick or straightedge tool as your guide. Make the line the length of the closet rod you purchased for the project. Put the line at least 12 inches from the back wall of the closet to allow room to hang clothes hangers on the clothes rod.
How many brackets do I need for closet rod?
Adjustable Closet Rod 1 TM Page 5 TM NOTE: Recommended 16″ bracket spacing. Maximum 32″ bracket spacing. First, measure the width of your closet. Measure 11-1/2″ from the rear closet wall.
How much weight can a wooden closet rod hold?
Never put more than 25-pounds of clothing on one of these rods or it will fail. The motorized version works with a remote control and can hold up to 60-pounds of clothing per rod.
How far should closet rod be from shelf?
A minimum of 10 inches is best, but it’ll depend on the size of your hangers. If there is a shelf above the rod, determine the vertical distance from the rod to the shelf; two inches should be suffice.
Can you hang closet rod with drywall anchors?
To securely install a closet rod in drywall: Drive screws into the wall stud or drywall anchor, securing the bracket in place. Repeat this process for additional brackets, making sure they are level with the first bracket. Set your closet rod in place and use it to hang your clothing.
Do closets usually have studs?
Closet shelves are usually anchored to the wall where the mounting screws can grab wall studs. If your walls are masonry, you likely don’t have studs at all. You’ll need the proper materials and methods to build a stud-free closet shelf.
Do closet rods need to be in studs?
Basic Installation It should be placed in front of a stud so you can screw into the stud to give it support. The typical height of a closet rod is from 60 to 80 inches, and both brackets should be at the same height, or the hooks you hang from the rod will slide to one end.
How deep is an average closet?
The standard minimum depth for a reach-in closet is 24 inches, but a closet intended to store coats or other bulky hanging items may need to be as deep as 28 inches. A closet less than 22 inches deep isn’t deep enough to allow hanging clothes.
How thick should a closet rod be?
A closet-rod dowel is usually between 1 1/4 inches to 1 3/8 inches in diameter. This diameter allows for plenty of hanging strength. It resists breakage, and will not bend when properly supported.
What is the standard depth of a closet rod?
Opt for a closet rod depth of at least 12 inches. You can avoid this clothing disaster by mounting the rod at least 12 inches from the rear wall of the closet. Keep in mind that the average closet has a depth of 24 inches.
How do you hang a dowel from the ceiling?
Using Bolts as Hangers Simply drill two 1/4-inch holes in a length of dowel and then mark holes the same distance apart in the shelf from which you want to hang the dowel. Drill holes in the shelf and insert carriage bolts. Affix the dowel to the ends of the bolts with 1/4-inch nuts.
Can you use PVC for closet rods?
The PVC pipe was much less expensive than buying custom closet rods and it worked just fine as the closet rods. I put in an extra bracket to support the top rail and prevent sagging in the middle.
Can you use a tension rod in a closet?
They are cheap and totally removable. They are great for those awkward areas where nothing else fits, and don’t do any damage to walls, closets, or cabinets. Some of their uses are obvious, but there are others you might not have ever considered.
What are closet rods made of?
Strength: HARDWARE DECOR offers closet rods constructed of three different materials: steel, stainless steel and aluminum. Closet rods made from steel are chrome plated. In addition to being the strongest, they are also very resilient.
How much space do hanging clothes need?
Shelves for folded clothes should be placed around 12 inches apart. 84 inches is considered the minimum height to hold double hanging rods. Blouses and shirts will take up about 1 inch of rod space, pants and skirts around 1 1/4 inches and dresses, jackets and suits about 2 to 3 inches.
How much weight can Rubbermaid shelving hold?
Total Weight Capacity: 350 lbs.
How much weight can closet rack hold?
For their closet shelving, you can typically expect to hold around 35 pounds per linear foot, unless you get the shelving with the ShelfTrack Hardware. Then, you can hold a very respectable 75 pounds per linear foot. If you get their Maximum Load Standard Shelving, you can expect to carry up to 600 pounds per unit.
How long is a hanger?
Standard-sized adult hangers measure 17-18 inches. Our over-sized hangers measure 19″ wide, giving more support to heavy coats or larger jackets.
How much weight can ribbed plastic anchors hold?
For reliable support in light-duty situations (up to 15 pounds), rely on the Qualihome Ribbed Plastic Drywall Anchor Kit.
