Table of Contents
Can I tile straight onto concrete floor?
In most cases, it is OK to lay tiles directly onto concrete. But make sure the surface is free of any contaminants, dust, moisture, etc, as these can prevent the adhesive from bonding. If the concrete floor is not in good condition, or may be at risk of cracking, an uncoupling membrane is recommended.
Do concrete floors need sealing before tiling?
You should seal the floor with a suitable primer that is compatible with the adhesive you buy. i.e. buy Ardex primer for Ardex adhesive, BAL primer for BAL adhesives Effectively it stops the draw (the sponge effect of the dry concrete) and creates a better adhesive bond.
What do you seal a concrete floor with?
Acrylic sealer – This easy-to-apply sealer is best for basements and other concrete floors that will not come into contact with oil or grease. Acrylic sealer sits on top of the concrete instead of seeping in, which makes it ideal for sealing interior floors.
Do you need a moisture barrier under tile?
During patching, most people usually wonder if they would need a moisture barrier under tiles. Well, yes. A moisture barrier should be installed to protect the flooring against moisture or moisture vapor.
Can you put ceramic tile over sealed concrete?
Attaching any tile product to sealed concrete is strongly advised against without first removing the sealer. The unmodified thinset would be the recommendation for use ON TOP of the DITRA when porcelain tile was used. DITRA is in fact a crack membrane but really isn’t intended to SOLVE any moisture problems.
What kind of thinset do you use for concrete floors?
Modified thinset is the product of choice for most tile installations because of its increased strength and bonding with minimal shrinkage, which means a reduced chance of cracks forming in the tile. WarmlyYours Radiant Heating recommends modified thinset mortar for nearly all tile and stone installations.
Does mortar stick to concrete?
Concrete slab was the foundation, original tile installation had mortar applied directly to concrete slab. Concrete, mortar or similar materials are not designed to stick or bond to old surfaces. You will not get any satisfactory results if you simply add new mortar to old.
What is the difference between cement and tile adhesive?
Cement is a cheaper material when compared to Tile Adhesives. You are likely to spend more on skilled mason and material while tiling with cement. Whereas, MYK LATICRETE Tile Adhesives help you curb wastage on material and resources used to tile the floor & walls and leaves no mess.
Do I need uncoupling membrane on concrete?
Most commonly, uncoupling membranes are used when laying tile over concrete. Although some substrates absolutely require uncoupling membranes, they can be installed on a range of surfaces, including cement mortar, backerboard, OSB, and plywood.
What is SBR primer?
Product description. BAL Bond SBR is a multi-purpose bonding and priming agent for both walls and floors. Priming a surface before you level or tile it will improve the physical properties of mortars. You’ll notice improvements in your mortar’s adhesion, durability, flexibility, waterproofing and workability.
How do you seal and finish a concrete floor?
How do you seal an indoor concrete floor? Allow recently poured concrete to cure fully. Let stains or overlays dry thoroughly before sealing. Remove baseboards or cover them for protection. Clean the floor and wait for it to dry. Wear protective gear and clothing. Open doors and windows for proper ventilation.
How do you waterproof a concrete floor?
When faced with damp in concrete floors, there are two options available: Dig up the old concrete floor, install a new damp proof membrane and lap up edges before replacing the concrete slab. Fully isolate the dampness in the floor using a surface Damp Proof Membrane (DPM).
Can I use PVA as a sealant?
PVA ADHESIVE & SEALER can be used with plaster, cement, timber, gypsum wall boards and paper. Properties as an adhesive include fast drying. It is also a readily dilutable primer for sealing applications or addition to cement and plaster to improve adhesion and cure.
Is moisture barrier necessary?
When moisture penetrates your flooring, it can cause mold, mildew, and the potential for water damage. A moisture barrier helps control the water vapor’s movement to help protect your floors. Therefore, if you’re installing floors in an area that sees moisture, even a little, a vapor barrier is needed.
Can you tile over a damp floor?
Short Answer: Yes, you can tile a damp basement if it’s rising damp, but it’s very important to use breathable tiles, such as unsealed quarry tiles or natural stone tiles that have been treated with a water-based sealer, such as LTP Mattstone H2O.
Do I need moisture barrier and underlayment?
Mostly concrete subfloors transmit moisture. Concrete is porous and allows moisture to pass through to your basement/room level. If the amount is more than what your underlayment can handle, then yes you will need a moisture barrier. If it doesn’t exceed the amount, then the underlayment can handle the job.
Can you put flooring over sealed concrete?
While concrete sealer may appear dry, it cures slowly over time. It is best to wait several weeks after application before installing your tile.
Can you tile over finished concrete?
Tiling can be done over stained concrete with proper preparation. You will need to either restore the concrete so it is close to its original condition or cover the stained concrete with a material such as cement board before tiling over it.
How do you remove sealer from concrete?
Start by removing any visible peeling and flaking and use a solvent based stripper such as Xylene to remove the previous sealer. (If concrete was dyed or stained, using Xylene can damage or change the color of the concrete.) Pressure wash the surface and allow concrete to completely dry.
