Table of Contents
Build the frame for enclosure. Nail 2x4s to existing posts to create the frame needed to secure the lattice panels. Run vertical 2x4s from the bottom plate to the existing deck. To install the lattice, measure vertically from the top of the panel (the bottom of the deck) to the ground. Screwing on Hinge.
What can I use under my deck instead of lattice?
If you don’t like the look of the lattice as a cover for under the porch, here are a few alternatives: Vertical wooden planks. Horizontal wooden planks. Wooden planks with a pattern or design. Rock porch skirting. Brick or stone. Alternative pattern vinyl lattice. Enclose the space.
How do you install lattice?
Instructions Measure and Cut the Stringer. With the tape measure, measure the inside distance between two of the deck posts. Install the L-Angles. Install the Stringer on the Deck. Measure the Coverage Area. Cut the Lattice to Size. Attach the Lattice to the Deck. Attach the Moulding Around the Lattice.
How do I cover the bottom of my deck?
Material Options for Hiding the Area Under Your Deck Lattice. Fence boards. Vinyl siding. Composite fascia boards. Stone faux.
How do you secure a lattice?
Use nails to secure the lattice to the lumber pieces, hammering nails every 12 inches. The lumber acts like spacers, allowing you to weave vines through the lattice if desired. It also gives plants better airflow than if the lattice rested flush with a solid surface.
Should I put plastic under my deck?
Plastic under the deck will trap moisture, increase rot and attract insects to your deck. Landscape fabric is a better alternative for stopping weeds from growing under the deck while allowing water to drain. Never put plastic under a deck except if its part of a dry deck system drainage system.
What is a floating deck?
A floating deck, also called a free standing deck, is simply a deck that’s not attached to any structure, including (of course) your house. Instead, you can put your deck’s structural members — posts, girders, and joists — on precast pier blocks set directly in the ground.
What do you put around the bottom of a porch?
The area under the front porch (or mud room) is referred to as a Porch Skirt or Porch Apron. The porch fascia board or skirt board directly under the porch floor, transitions the porch to the porch skirt. The porch skirt, like the foundation, visually anchors the house to the ground.
Does Lattice need a frame?
Lattice is typically purchased in either 24-by-48, or 48-by-96-inch sheets and cut to size depending on use. Framing is necessary after cutting.
What do you use for deck skirting?
Deck Skirting Materials & Styles Wood Lattice. When you imagine a deck skirt, a wooden lattice is probably the first thing that comes to your mind. Solid Wood. Solid wood boards are another popular deck skirting option that’s easy to customize. Composite. Faux Stone. Brick. Shrubs and Plants. Metal.
How long does vinyl lattice last?
This type of lattice is considered permanent and can last up to 30 years. Most sellers guarantee it for a lifetime of use. This material requires virtually no maintenance, but it does have the highest price tag. This may not be an issue if you are using the lattice panels for a small project.
Can you use screws on lattice?
Lattice screws have a sharp, pointed tip so you can install them without pre-drilling pilot holes. Installing lattice panels with screws takes a little more time and is slightly more costly than installation with nails, but it ultimately produces a longer-lasting outdoor structure.
How much does it cost to install lattice under deck?
A simple lattice skirting consisting of lattice hanging down from the deck rim joist can cost as little as $2 a square foot.
What do you do with area under deck?
8 Under-Deck Design Ideas to Fill Your Empty Space 1) Add Lattice as a Deck Option. 2) Skirting. 3) Build a Shed Under the Deck. 4) Build a Patio Under Your Deck. 5) Add a Patio Swing. 6) Cover the Ground in Weed Blocker Fabric and Gravel. 7) Create an Under-Deck Play Area for Children. 8) Completely Finish the Space.
How do I stop rain under my deck?
The best way to waterproof under your deck is with a deck drainage system installed during construction. A drainage system diverts water away from the joists and beams. An over-the-joist deck drainage system such as Trex RainEscape provides 100% protection from the damage caused by wood repeatedly getting wet.
How do you screen under a deck?
Lay down the screen fabric on top of the joists, and then place the deck board on top to hold it in place. The screen is sandwiched between the bottom of the decking board and the top of the joists, providing an effective barrier. Some systems, like the SCREENEZE screening system, include this.
What screws to use with lattice?
Use #8 stainless steel sheet metal screws to maintain the beauty of your project. Place fasteners 24″ apart for best results.
Can you nail vinyl lattice?
When installing vinyl lattice be certain to use stainless steel nails or fasteners to secure your lattice sheets. This will prevent rust stains on your lattice.
Do you need a vapor barrier under a deck?
Do not install a vapor barrier beneath the deck. Water vapor from the soil can cause severe cupping of the decking. The underside of the decking boards readily absorb moisture that evaporates from the soil.
Are Floating decks a good idea?
Yes, a floating deck is a good idea if the deck is low, not attached to the house or built close to trees. A floating deck will save you both time and money during construction. But a floating deck is a bad idea if the deck is tall or is attached to the house.
Do floating decks need beams?
2×5=10 A floating deck less than fourteen feet deep needs two beams. One on each end, more if you use smaller joists but let’s assume you use larger joists like 2×8. A deeper deck will need larger joists or closer spacing. For this deck, you will need to purchase a minimum of 10 deck blocks.
How do you cut lattice?
Cutting Your Lattice Use a circular saw or jigsaw with a carbide tipped blade to cut the lattice. When you make your measurements, allow 1/4″ on either side to allow for expansion and contraction of the panels. If you have a slope, you will need to cut the lattice to match the grade.
Does deck skirting need ventilation?
Discovering that a deck’s skirting requires one square foot of ventilation for every 150 square feet of deck to allow moisture to escape from under the deck. Allowing the decking and substructure to dry, preventing rot, mould and decay from destroying the deck.
