Table of Contents
How to Connect the Harp on a Lamp Unplug the lamp from the electrical outlet and unscrew the light bulb. Place the lamp on a level surface. Raise the harp’s two sliding cylinders, called ferrules, to reveal the notched ends of the harp base. Straighten the harp if it’s sitting crooked. Hold the lampshade right side up.
How do you convert Uno lamp shade to harp?
How To Use an Uno Shade with a Harp & Finial Lamp 1 & 2. Unscrew the finial and then squeeze the harp to remove it. Pop the socket itself apart. Remove the top portion of the socket to reveal wire connections. Thread the wire through the ring of the uno shade and then through the socket cup.
Can you use a lamp without a harp?
I’ve always felt like the scale of my lampshades was off on my lamps by the fireplace. The lamps are plain without any harps to attach different shades that need a harp.
How do I know what size harp for my lamp?
If you require a different size harp than the one you have on your lamp, check under the finial base (see Fig. 1) and you will see a number that will indicate the height-size of the harp. With this number in hand you will have a reference point for acquiring a new harp that will best suit your needs.
How do you put a harp base on a lamp?
If you wish to remove the harp, for adjustment or replacement, first unscrew or otherwise remove the lamp finial above the lampshade, remove the shade, and gently squeeze the harp inward just above the harp base. The harp locks into the lamp via notched “legs” that slide into the short slotted arms of the harp base.
What is a spider lamp shade fitter?
1. Spider Fitter Shades. The spider lamp shade is the most common type of fitter for table and floor lamp shades. Spider fitters sit atop the lamp’s harp (the U-shaped metal part of a lamp that fits around and protects the light bulb). Once placed on top of the harp, spider fitters are secured to the lamp by a finial.
What is a harp lamp shade?
A lamp harp is the component of a lamp to which the lamp shade is attached. It typically comes in two separate parts, a saddle which is fastened under the lamp socket, and the harp itself which consist of a lightweight frame attached to the saddle at its lower end and extending upwards to a point above the bulb.
Can you convert UNO shade to spider?
EASY INSTALLATION – Converts your Standard “Spider-Fitter” Lampshade to fit on Slip Uno Lamp Base Lamp. (drop is the distance from the top of the shade to the center washer. QUALITY – hardened steel construction. Durable steel with brass finish, this will be the last harp fitter you will ever need to buy.
How do you install an UNO fitting lamp shade?
It attaches directly to the base. Connect the shade to the base before putting in your light bulb. To do this, turn the shade so that the metal arms are on bottom. Then simply press the shade onto the lamp base. The metal ring on the shade will fit snugly over the lamp base.
How do you tighten a lamp harp?
A-Take off the shade to expose the socket, then look for a small setscrew in the bottom of the socket`s base. You will notice that this socket base screws onto the top of a small-diameter threaded pipe, so you can tighten it back down by turning the base of the socket clockwise while holding the lamp base steady.
What is a Euro fitter?
A Euro fitter joins the lamp to the light between two parts surrounding the bulb, held in place by a thin gap that exists between the bulb socket and base. European Fitters are also known as ES fittings (Edison Screw or European Standard).
Do all lampshades fit all lamps?
If you are unsure of what shape lamp shade to choose, match the shape of the lamp shade to the shape of either the lamp or the lamp base. A good lamp shade will cover all of a lamp’s hardware. For a balanced look, a table lamp should have a lamp shade that is approximately 2/3 the height of the lamp.
How do you measure a harp?
The measurement for harps is from the “base” (that’s the bottom as shown in the photo) to the bottom part of the screw on top. If your lame already has the base attached, you can just use the top part of the harp.
What is an empire style lamp shade?
In general, the empire style is one in which the top diameter of the lampshade is about ½ of the diameter of the bottom of the lampshade; the style exhibits a straight, gentle slope from the top of the lampshade to the bottom of the shade.
How should a shade fit a lamp?
The shade should be twice as wide as the lamp base, and one third of the total height of the lamp. So for a 6-inch lamp base, the shade should be at least 12 inches wide. And if the total height of the lamp (including the bulb and harp) is 24 inches, the shade should be 8 inches tall.
How do you replace a harp base?
Work on a comfortable table or counter top. Remove the socket cover by locating and pushing in on the spot marked “press” to loosen the socket. Loosen the screws and remove the wires on the sides of the socket, but leave the screws attached. Replace parts in reverse of the order in which they were removed.
How do you attach a lampshade to a table lamp?
How to Change a Lampshade Unplug your lamp at the electrical outlet. Remove the current shade and harp by unscrewing the finial, removing the shade, and squeezing the harp out of the saddle. Squeeze the new harp into the saddle. Add your new shade and screw on the finial to secure it.
