Table of Contents
How do you remove a pulley without a puller?
If you’re adamant that you want to do it without the puller tool, here’s how: With the pump taken off the vehicle, place it in a vice and use a piece of metal pipe and a hammer to tap the wedge between the pulley and the pump. Heat the center of the pulley with the blowtorch and pull it off.
How much is a pulley puller?
Compare with similar items This item OEMTOOLS 27031 Power Steering Pulley Puller and Installer Kit, Removes and Installs Power Steering Pump Pulleys on Most Domestic Vehicles, Ford, GM, VW OTC 4529 Power Steering Pulley Puller/Installer Set Price Unavailable $38.99$38.99 Sold By — National Tool Warehouse.
How do I remove a pulley with a key?
Place the assembly over the key, and then thread the bolt into the shaft as far as it will go. Spin the nut downward against the block. Then use a wrench to apply enough force on a nut to remove the key from the shaft. If you apply enough downward movement, the key will be extracted.
How do you remove a harmonic balancer pulley without a puller?
Most vehicle engines are now equipped with a pulley that holds the harmonic balancer apart from the center bolt. To remove the pulley, you need to rotate it a little with a screw driver’s help and pull it out using a pickle fork. You might not need the pickle fork; you can do that with bare hands.
What tool is needed to remove and install a power steering pump pulley?
Using an impact wrench or regular socket and ratchet, remove the bolts that hold the power steering pump onto the bracket or the engine block. Usually there are two or three bolts that need to be removed.
How do you remove a power steering pulley bolt?
Locate the power steering pump and the mounting bracket that secures it in position. Use a socket and ratchet to loosen the adjuster bolt of the power steering pump and pulley. When this adjustment bolt is loosened, the pump will pivot on an axis, making it possible to loosen its drive belt.
Are pulley pullers universal?
You can quickly and easily remove serpentine pulleys on most foreign and domestic passenger vehicles using press type pulleys with the Powerbuilt universal pulley puller kit. This versatile tool fits a wide range of vehicles thanks to jaws that adjust from 1-1/4 inches to 7 inches wide.
What is a shaft key?
Metric Shaft Keys are rectangular or square shaped keyways that are used to lock rotating elements onto a shaft. Shaft Keys fit into slots cut into a shaft and a component such as a pulley or sprocket creating an assembly that rotates as one unit.
What tool is used to remove crankshaft pulley?
The tool suitable for removing a crankshaft pulley is a half-inch drive impact gun. You could also use a torque wrench to secure it properly.
How do you attach a pulley to a shaft?
To attach a pulley, a mechanic tightens mounting screws, which draw the tapered surfaces of the bushing and pulley hub together. Forcing the mating tapers together creates a wedging action between the bushing and pulley, and between the bushing and drive shaft.
How do you install a pulley on a keyed shaft?
Where would you use a jaw type puller?
3-Jaw Puller You can use them to remove gears, pulleys, wheel hubs, all kinds of hard to remove parts. They come in several sizes and are inexpensive. Every garage should have three sizes of 3-jaw pullers in the drawer.
What size jaw puller do I need?
One rule of thumb in choosing a puller is the center bolt diameter must be at least ½ the diameter of the shaft from which the object is being removed. It is impossible to predict the exact force needed for every pulling situation. The amount of press fit and force of removal can vary greatly between jobs.
What does a bad power steering pulley sound like?
A loose power steering pump pulley or mounting bracket will make a rattling sound too. A rattle sound can be caused by a loose rack due to wear. It could also indicate a loose serpentine belt or idler pulley bearings beginning to fail.
Why is my power steering pulley wobbling?
What causes a power steering pulley wobble? – Quora. This happens when the bearings are going bad. You may also hear noise when the pump is being turned. As the bearings on the impeller go bad it will start to make noise as the pump is turning.
Should a power steering pump pulley move in and out?
The pulley shaft will commonly move in and out of pump body even on brand new units, I’ve seen 1/8″ before. Normal.
Should power steering pulley spin freely?
Without the friction of the drive belt and the engine NOT running, all driven pulleys should turn freely without noise when spinning by hand. The P/S pump and water pump pulley will have some drag (resistance) but still turn freely with little resistance when turned relatively slowly.
Is power steering pulley reverse thread?
No, there’s a third bolt on the bottom.
Do you need a harmonic balancer puller?
The harmonic balancer is a part of the car’s engine. The outside is usually aluminum, but it needs a special tool, called a harmonic balancer puller, to remove it from the crankshaft of your car’s motor because it has a rubber mounting to the crankshaft.
How do you remove a stuck crankshaft pulley?
4 Ways To Remove A Stuck Crankshaft Pulley Bolt Soak in Lubricant. Although the bolt sits on the side of the engine, you can use putty to create a sticky dish for your lubricant of choice. Rent A Powerful Impact. Try a Long Breaker Bar. Bump the Starter. Take It To A Shop.
What are the three types of pullers?
These pullers include bearing splitter plates, 2 and 3 arms bearing pullers, internal bearing pullers, bar type puller &slide hammer puller.
What is a slide hammer puller?
Rugged slide hammer pullers can help with pulling jobs involving gears, bearings, oil seals and more. A slide hammer can also pull out dents in fenders, side panels and other vehicle body parts.
