Table of Contents
Start at the most forward point of the bunk, raise the bunk until it touches the bottom of your boat and tighten until the bunk is in place. Repeat this step moving down your trailer until all of the bunks are touching the bottom of your boat, and are secured in place.
How should a boat sit on the trailer?
Set boat on trailer while maintaining no less than 2″ gap between keel and tongue plate cover. The end of the bunks/rollers should be flush with transom and the boweye should reach the winch post. If this is so, the rear pivot should remain in the A-position.
Should a boat sit level on a trailer?
Your boat trailer should always be as level as possible when towing. This is because you want the weight of your boat to be evenly distributed across the axles of your trailer. This allows for better tracking and handling and ensures you’re being as safe as possible.
Are the bunks on a boat trailer supposed to move?
Jetboaters Captain. @Bdog is correct. You want them to move a bit so the boat can settle onto them fully each time. If you tighten them down too much and they don’t give, then you run the risk of the boat sitting on only a portion of the bunk and creating a larger opportunity for a wear in the gelcoat.
Should boat rest keel roller?
In the full forward position on the trailer, the boat rest on the two boards. It does indeed look like you need to move your keel rollers up towards the bottom of the boat until they are touching but not supporting the full weight.
How far should side bunks be from boat?
A spacing of 1-inch between the boat’s hull and the surface of the carpeted bunks is usually best. This allows enough wiggle room for loading the boat while keeping it in a reasonably snug fit in the bunks.
How long should boat bunks be?
Ideally, the bunk boards should be at least half as long as your boat and run from the stern (or a few inches beyond it) to the bow as far forward as you like.
Should my trailer be level when towing?
When towing, trailers should be level to improve stability, braking performance, and ground clearance. A level trailer will prevent poor towing characteristics, like sway, and uneven tire wear. Adjusting the trailer to be level is important for safety.
How much overhang should a boat trailer have?
Note that on boat trailers the length of the front load carrying area is often difficult to define, so the maximum allowable rear overhang of 3.7 metres will normally apply.
How should a jet ski sit on a trailer?
The jet ski should always sit on the trailer in a centered position as it has to be balanced on the trailer. Also make sure to pull it up completely until the bow reaches the bow stop and attach the safety chain!May 24, 2020.
How do you set up keel rollers?
Make sure you install high quality trailer rollers. set your width measurement first. Next, set your keel roller height with a string line running from front to back. Back all the wobble rollers off about 10-15 mm (lower) and then pull the boat back on ensuring the boat is on the center of the keel rollers.
Where does a keel roller go?
In regards to installation, these will need to be installed towards the stern of the boat, in the center of the trailer. This would be the only place that would allow them to effectively center your boat on the trailer.
How tight should boat guides be?
But since guide-ons are not meant to support weight like a regular bunk you don’t want it so close that the boat could damage the system, but they have to be close enough to help guide the boat on accurately. If it is as rough as it sounds like then I would say maybe 3 inches on each side would work.
How tall should boat trailer guides be?
Guide posts are L-shaped and available in different widths and heights. Most are 40″ to 60″ high. They are simple to install—just attach them to the trailer frame with brackets and bolts provided, and set them between the uprights a distance about 2″ wider than the widest beam of the boat.
What is the best wood to use for boat trailer bunks?
For wood, pressure-treated pine is the industry standard for trailer bunks. Popular alternatives are oak, cypress and other hardwoods that add even more durability. Composite boards used for patio decking are other options, but pressure-treated pine is a proven material with economic benefits.
How do you make a boat slide trailer easier?
Use a silicone spray such as (WD-40 Water Resistant Silicone Lubricant). This way is very effective and your boat will slide off the bunks fast. Make sure to have a rope or something to hold the boat from getting away from you.
How long should my boat trailer be?
Length should be measured from the farthest point at the bow to the end of the hull’s running surface. In general, trailers are typically about two feet longer than the boat itself.
