Table of Contents
Turn the spa on and wait for PR (Priming Mode) to appear on the topside display. Press the JETS button to turn on the pump and let it run for 10 seconds. The pump should be running in low speed. Press the JETS buttons again and let the pump run in high speed for 10 seconds.
How long does it take to prime a hot tub pump?
Control Panel Priming Turn your jets on low for 10–20 seconds. Switch your jets to high for another 10–20 seconds. Repeat until the water pressure is normal and jets are working without any gurgling or air bubbles.
What is priming mode on a hot tub?
Once power is initiated to your hot tub it will go through a priming mode. The purpose of the priming mode is to manually activate each spa pump prior to the automatic heat cycle being started. Typically, cycling each pump a few times will prime or purge any air from the plumbing.
How do I know if my hot tub has an airlock?
As mentioned above, the most common sign that your hot tub has an air lock is the jets not working when powered on. This can include nothing coming out of your jets when they are turned on or even a humming sound coming from the jets or pump.
How do you prime a hot tub heater?
How to Prime a Hot Tub Pump Shut down the hot tub. Turn off the power at the wall. Take the handle off the massage selector that’s supplied by the pump you need to prime. Turn the massage selector’s cap counter-clockwise a little. Turn the massage selector cap clockwise to tighten it when the hissing stops.
How do you stop an airlock in a hot tub?
Preventing Hot Tub Air Lock One of the easiest ways to prevent hot tub air lock is to purge air from the lines as you are re-filling the hot tub. Instead of dropping the hose directly into the tub, stick the end of the hose into the filter well, and leave all jets completely open.
How do you shock a hot tub for the first time?
To shock your hot tub, simply follow these easy instructions. Adjust the pH levels of your spa’s water to between 7.4 and 7.6. Remove the hot tub cover so your spa can breathe while being shocked. Turn off the air to the jets but leave the circulation pump running so the water is moving but is not too agitated.
How do I know if my hot tub circulation pump is working?
Check that your power is on, the breaker or GFCI test button are not tripped, all valves are in the open position. Follow the circ pump plumbing, and look for any kinks in the hose. Pull out the cartridge filter to see if flow improves and the circulation pump is doing better.
How do I get rid of an airlock in my water motor?
How do you get rid of an air lock in a water pump? To release the blockage, simply open both valves (the main valve and the block valve) and let the water line pressure force the air out of the blocked valve. Let it sit for a few minutes, making sure to close the closed air valve first.
What causes hot tub jets to not work?
Hot tub jets that are not working can be caused by air leaks, clogged drain covers, low water levels, dirty filters, bad pumps, improper jet adjustment, closed valves, electrical problems, clogged pump impeller, and issues with the hot tub controls. These issues should be troubleshot carefully.
What does prime a pump mean?
Key Takeaways. Pump priming refers to the steps taken to stimulate spending in an economy during or after a recession. Generally, it involves pumping small amounts of government funds into a depressed economy to encourage growth.
Do you bleed a radiator when it is on or off?
Turn off your heating. You can’t bleed a radiator when the heating is on, as it may be too hot to touch. You could also get hot water spraying out of the radiator. Use your radiator key to turn the valve at the top of the radiator.
How do you prime a small water pump?
How To Prime Your Water Pump Make sure the power is turned off. Never leave a pump plugged in while you’re working on it. Gain access to the pump system. Check for damage. Test a hose. Open the relief valves. Attach the hose. Turn on the water and wait for it to enter the tank. Turn the power on.
How do you prime a diaphragm pump?
Slow the pump down to prime. To solve this priming issue in a matter of seconds, slow down the pump by using the air regulator to decrease the air pressure entering the air valve.
Why does my chlorinator says no flow?
The most common reason for low or no flow is that the baskets are full of debris. By checking and emptying both the skimmer basket (by the pool) and the pump basket (inside the pump) will free up the water flow, allowing the system to fully ‘prime’ and function at full capacity.
Should chlorinator be full of water?
The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.
Where is the reset button on hot tub pump?
Locate the spa’s high-limit reset. This is a red button found on many spa packs. It may be located on the heater and covered by a rubber nipple.
Will an airlock clear itself?
Airlocks do sometimes fix themselves, but it isn’t a risk worth taking. Airlocks occur when air becomes trapped in the hot water or central heating system. Vapour becomes caught in a high point of the pipework because the gas is less dense than the water in the system.
Is shock the same as chlorine?
1) What is the difference between chlorine and shock? Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
