Table of Contents
When should I pin my miniatures?
Pinning is a skill that most miniature enthusiasts pick up at some stage; essentially it’s a method of securing a limb or other item to a miniature. It’s used in situations when superglue is not strong enough to hold the model together which is pretty often in my experience of superglue and metal minis.
Do you need to pin metal minis?
One of the downsides of metal miniatures is that the bond between two metal components can often be quite brittle, especially if you’re using superglue. Pinning is a very straightforward process of strengthening the connection between two metal parts by way of a piece of wire, which acts as a support beam of sorts.
Can you drill pewter?
Bit OTT for pewter. Any HSS drill bit will do it.
How do you clean resin miniatures?
You will need some warm tap water and a mild abrasive cleaner, such as washing-up liquid, don’t use any bleach. Simply place the parts into the soapy water and leave them to soak for 5-10 minutes, then thoroughly scrub each part with an old toothbrush. When finished dry each component.
How do you glue Warhammer figures to base?
You must use intant glue and keep the miniature and the base together about 10 seconds. Next put the miniature on the table and use other thing (other miniature for example) to keep it on the right position. Good luck!Nov 5, 2014.
What is a pin vise drill?
A pin vise (or pin vice in the UK) is a miniature drill or twist drill that is a useful, fairly inexpensive specialized hand tool used a lot in miniature woodwork. Pin vises, as the name suggest, hold thin, long cylindrical objects (like a pin or wire) by one end.
Do you need to wash metal miniatures before painting?
It’s always a bit of a toss-up, painting minis without washing them first. I often don’t bother, but I’ve had cases where spots of remaining oil from the manufacturing process prevented primer from properly sticking to the surface.
Do you prime metal miniatures?
For metal miniatures, you want a primer that hardens and for lack of better words, “sticks better” to the metal or resin surface. This means you probably want an enamel-based primer. Enamel is a much harder substance than the polyurethane material of a lot of non-rattle can primers.
How do you prepare metal for miniatures?
Instructions Clean the Base Casts. Remove any extra metal, using fine-grit sandpaper, fine files, and a craft knife or a dentist’s tool. Fill the Base Casts. Clean the Base Cast Again. Apply a Base Coat of Paint. Apply the Base Paint Colors. Apply Details to Your Metal Miniatures. Overcoating Painted Metal Miniatures.
Which purpose the pin vice is used?
A pin vice is commonly used in jewellery making, where it can be used to twist wire and drill holes, and in model building, where it is also used to attach pieces together and to create detail. In addition, pin vices are used in watch repair.
What is the function of pin vice?
Pin vises are tool holding devices that allow small tools to be held in place with positive acting jaws (think mini-chuck). These pin vises are available a few collet, handle, end and length varieties.
What are cobalt drill bits for?
Cobalt drill bits are incredibly strong. They can be operated at much higher speeds than a standard HSS drill bit. The ability to withstand heat means that cobalt bits perform for long periods without cooling or the need for cutting fluid. They are most often used to cut through hardened and abrasive materials.
Why can’t I drill through metal?
Drilling into a hard surface requires the use of specialized drill bits. Regular drill bits are not designed to cut through metals. Therefore, they can easily wear away. So you need hard bits which can drill through metals without being damaged.
When drilling metal should you use cutting oil to lubricate it?
We recommend you always use a metal cutting fluid or lubricant when you are drilling. There are 3 main reasons you should use a cutting paste: Reduce friction. Assist cooling.
What is wet palette?
The basic science behind a wet palette is that a layer of absorbent material both holds and gradually delivers moisture onto a piece of material which can be hydrated by water, yet is not so porous as to risk flooding your paints. Your paint being hydrated, it won’t dry out ahead of time.
Can you prime miniatures with acrylics?
Acrylic paint doesn’t adhere very well when applied directly to metal, resin, or plastic, no matter how well you clean your miniature. Primer bonds well to metal and plastic. Without primer, acrylic paint can flake or chip off easily.
Do plastic miniatures need primer?
Do I Need to Prime Plastic, Metal, or Resin Miniatures? Priming a model helps paint stick and gives any paint job long-term durability. Without a primer, even the very best acrylic paint will chip and flake off in no time during handling, transportation, or even while you are painting the model!.
Is Abaddon Black a primer?
Abaddon black could be used as a primer, I suppose. It has a matte finish and is intended to be used to give a layered textured look. No this is not a primer it is a base, Games Workshop used to sell a paint primer called Imperial Primer, but now they sell primers only in spray cans.
Can you use Gorilla Glue on plastic models?
Does Gorilla Glue work on plastic? According to the manufacturer, Gorilla Glue can work well with many types of plastics, but it’s not recommended for use with polypropylene or polyethylene plastics, or with rubber that has a high oil or plasticizer content.
Do you need glue for Warhammer minis?
Glue is essential for Warhammer. Whether assembling your new shiny plastic army, fiddling with bases or trying to glue together that pesky old metal model – you are going to use glue. Having bad glue can cost you a lot of time and frustration.
Can you glue Warhammer models?
For plastic miniatures, you will need some plastic glue – specifically poly cement glue. Citadel is fine, but I prefer the small nozzle of the Revell. It just gives a bit more precision, and I hate getting glue on places I do not want. To remove excess glue a bit of paper towel is very handy.
