How To Overlap Drip Edge

Should I overlap drip edge?

The drip edge should always be installed with the flashing under the felt on the eaves side and over felt on the rakes unless local code dictates otherwise. For proper water drainage, the drip edge on the rakes should always overlap the drip edge on the eaves. This works out correctly if you do the eaves first.

How far do you overlap drip edge?

Adjacent drip edge pieces should be lapped minimum 2 inches. Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch.

How much do you overlap flashing?

Place each step flashing piece about ¼ inch short of the bottom edge of the shingle that will overlap it — just enough so that the flashing piece is not visible when the overlapping shingle is in place.

Does drip edge go over or under underlayment?

According to most building codes and manufacturer recommendations, the drip edge should be installed beneath the underlayment along the eaves of the roof. But over the underlayment along the rake edges of the roof. Understanding the proper way to install the drip edge will only get you so far.

Should I overlap flashing?

Flashing should overlap the roof-covering material, but on asphalt shingle roofs, for aesthetic reasons, the part of the headwall flashing that extends down over asphalt shingles is often covered with a course of shingle tabs. Wind-driven rain can enter at these gaps, causing roof leaks.

Do you put drip edge on before tar paper?

Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.

Can you install drip edge after shingles?

The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.

Where should drip edge be installed?

Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.

How much do you overlap tar paper?

Roofing felt is required to overlap 2 inches over the lower felt course. The overlapping felt creates a secondary barrier for moisture and wicks water away from the shingles above and the sheathing below. Therefore, a 2-inch overlap provides redundancy at the edges where the barrier is weakest.

Does rain gutter go under drip edge?

It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. If gutters are installed below the drip edge, water can drip behind the gutter and cause damage to the wood supporting the gutter system.

Is a drip edge necessary on a shed?

Shed roof drip edge is essential in keeping your structure watertight. However, there are tons of ways to mess up a drip edge installation. For instance, nailing drip edge too close to your shed will still allow drips down the fascia board.

What kind of nails do you use for drip edge?

The drip edge is nailed in place using 1-1/2 galvanized roofing nails. A felt-tip marker works great for marking cuts. And, again, prying open the end with a small flat bar allows the pieces to overlap cleanly.

Can you install drip edge without removing gutters?

If the home has no gutter, the drip edge will prevent the water from running down the fascia and onto or into the soffit cavity. However, without the drip edge, the water sticks to shingles, potentially working its way under the shingles to cause a leak.

How do you attach drip edge to an existing roof?

Make sure the outer edge extends over the gutter. If it doesn’t, pull the drip edge out slightly from under the shingles. Secure the drip edge with roofing cement. Apply a continuous bead of cement along the top of the drip edge, then press down on the shingle.

Does a metal roof need a drip edge?

A drip edge is not needed for metal roofing. If you make sure to overhang your metal roofing at least an inch, the drip edge is not necessary at the eaves and rakes.

Should I use 15 or 30 lb felt?

If your roof does not have a steep pitch, you can use #15. This weight of felt is a good economic choice if you have a standard roof. But if your roof has a steep pitch, #30 is a better option because it is thicker and tears less during installation. With #30 you get a thicker layer of underlayment and protection.

How Much Should felt overlap?

Always ensure there is at least 5cm of overlap between each sheet, and nail down the felt from the centre outwards as before.

How far do you overlap underlayment?

Overlapping 19 inches will ensure that the underlayment is at least two layers thick all over the roof. So, underlayment on low-slope roofs should overlap 19 inches. Remember that underlayment on steep-slope roofs should overlap 2 inches.

Should there be a gap between gutter and fascia?

The best installation method is to leave a gap between the drip edge and the fascia board, about the width of a finger. The shingles should also overhang the drip edge 3⁄8 to 1/2 an inch.

What is the difference between drip edge and gutter apron?

The most obvious attribute that distinguishes a gutter apron from a drip edge is the fact that a gutter apron is more of an L-shaped metal rather than a T. A gutter apron also comes in metal strips with aluminum and steel sheets. Like drip edge, a gutter apron may be available in many different colors.