Table of Contents
Measure the length and width of your driveway in feet. Multiply the length by the width to get surface area and divide the result by three because 4 inches is 1/3 of a foot. You now have the volume of gravel needed in cubic feet. Divide the volume in cubic feet by 27 because there are 27 cubic feet in a cubic yard.
What is the best kind of gravel to use for a driveway?
Pea gravel is popular gravel for driveway aesthetics. It’s made up of round, small stones that can come in many different colors. This type of gravel will easily migrate and spread under the weight of vehicles, though, and needs to be stabilized for long-term, maintenance-free usage.
How do I calculate how much gravel I need?
Measure the length and width of the area in feet and multiply the figures together. Multiply your area figure by the depth of gravel that you wish to use, ensuring your measurement is also in feet. If your depth is in inches, divide it by 12 first. You now have a cubic feet volume figure.
What area does a ton of gravel cover?
Type 3 Aggregate Calculator Un-compacted Cloburn aggregates weigh 1.4 tonnes per cubic metre. Therefore if you wish to apply them at a 50mm depth (the normal depth for a driveway) one tonne will cover 14 square metres.
How do I calculate driveway rocks?
To measure the driveway in cubic feet, multiply the length by width by depth. For cubic yards, divide the total cubic feet by 27. Because one cubic yard of gravel is equal to 1.13 tons, you can multiply your total cubic yards by 1.13 to convert this measurement to tons.
What size gravel do I need for my driveway?
What is the Best Size of Gravel for a Driveway? Generally, the gravel for driveways should be between about 3/8 and 3/4 inches in diameter. They should be larger as compared to gravel that is used in pathways. Moreover, you need to consider the number of fines or the small granular material in the gravel.
Is 20mm gravel OK for driveway?
Ideally you should use 20mm Golden Gravel for your driveway as the smaller sized 10mm may get stuck in your tyre treads. The advantage of using gravel for your driveway is that it will require very little maintenance ensuring you lay a fabric membrane down before laying your gravel.
How many inches deep should a gravel driveway be?
A standard driveway is between 12 and 18 inches deep. Each of these gravel layers is a minimum of four inches deep, and some folks recommend making each layer as much as six inches. If you have a large area to dig out for your new driveway, the idea of a shovel and wheelbarrow may not be very appealing at this point.
How many square feet will 10 tons of gravel cover?
How much area does 10 tons of gravel cover:- typically, as 1 ton of gravel cover around 108 sq ft area for 2 inch depth, so 10 tons of gravel = 108 × 10 = 1080 sf coverage, therefore 10 tons of gravel can cover around 1080 square feet or 120 square yards or 100 square meters area for standard 2 inch depth.
How deep should my gravel be?
Gravel 1-1/2” to 2” will need to be 3” deep, and 2” to 4” gravel needs to be 4” deep. This is to provide complete coverage and so you cannot see the landscape fabric (weed-mat) through the gaps in the gravel.
What is the cheapest gravel for a driveway?
Cheapest gravel for driveways. The cheapest gravel for driveways is crusher run, crushed shells, crushed concrete, slate chips, recycled asphalt, and pea gravel, which all cost $15 to $30 per yard, or less than $1 per square foot when purchased in bulk from a quarry.
How many square feet will 5 tons of gravel cover?
Regarding this, “how much area does 5 tons of gravel cover?, typically, as 1 ton of gravel cover around 108 sq ft area for 2 inch depth, so 5 tons of gravel = 108 × 5 = 540 sf coverage, therefore 5 tons of gravel can cover around 540 square feet or 60 square yards or 50 square meters area for standard 2 inch depth.
How many yards of gravel does a dump truck hold?
A standard sized dump truck is always recommended for your project. It can carry about 10 to 14 cubic yards of dirt or 12 cubic yards of stones or 15 yards of topsoil or 22 yards of mulch or 16.5 yards of gravel per truckload.
How much gravel do I need for a 2 car driveway?
According to the Home Depot, 4 to 6 inches of rock or gravel is needed for a driveway. Convert your estimated rock depth in inches to feet by dividing the number of inches by 12.
How much will a ton of gravel cover?
A ton of gravel will cover approximately 100 square feet, 2 inches deep.
How many cubic feet are in a ton of gravel?
How much is a ton of gravel? A ton of gravel with average-sized pebbles is about 0.705 cubic yards, or 19 cubic feet, assuming it has been screened for debris and contains no leftover dirt, sand, etc.
What size is #3 gravel?
#3. Crushed stone #3 includes stone between 1/2 and 2 inches. This material is a great choice for railroad projects and those that require drainage.
What size is #2 gravel?
This primarily 1″ crushed, washed gravel with a top size of 1-1/2″ is often used for drainage around perforated pipe, under concrete slabs, and as a coarse driveway topping for soft, very muddy driveways.
What size is number 4 gravel?
#4 Description 1 to 2 ½ inch sized stones or roughly golf ball to egg size material. Generally used as a base material and topdressed with smaller stones or used as a decorative cover material that will not be walked on.
