Table of Contents
Insert your Honeywell safe key into the lock and turn it clockwise as you turn the handle of the safe’s door. Once you’ve accessed your safe, turn the emergency key counterclockwise, remove it from the keyhole and close the door of your safe.
How do you open a Honeywell safe without the key?
You can still open your digital safe without a key by restoring power to the keypad so you can enter your passcode. If you’ve forgotten your passcode, you can reset it by using a thin rod or wire to press the reset button on the inside of the door panel.
How do you open a safe if you forgot the combination?
If they can’t help you, your local locksmith can. If the safe is a dial, and you were able to find the serial number, the locksmith will most likely will be able to retrieve the original combination to the safe. So long as the safe combination has never been changed, this will open the safe.
How do I reset my Honeywell safe code?
To reset the primary user code, look for the “reset” button, which is often in the inside edge of the safe door. Press the button. You should see a yellow LED light and hear beeps. You can now enter three to eight digits to create your new code.
How do you change the combination on a Honeywell safe?
Once the safe door is open, locate and press the small reset button located on the inside edge of the door, the keypad will beep twice and the green LED will light up. 2. Enter a new 3-8 digit Primary user code followed by the # key, the green LED will again light up and the keypad will beep.
How do you lock a Honeywell safe?
LOCK SAFE WITH A NEW PASS CODE 1. Close the safe door and hold it closed. 2. Enter a new (3-6 digit) pass code followed by “lock”.
What does E code mean on Honeywell safe?
If you enter an incorrect pass code followed by “LOCK”, the safe will not open and the LED panel will display ”E-COdE”. This safe includes a set of Override Access Keys. In the event your safe will not open because of weak batteries or a problem with the current pass code, then it can be opened with the override key.
Why is my Honeywell safe beeping?
If your batteries are completely dead and you cannot open the safe by using the digital keypad, use the override access key to open safe and access the battery compartment. Safe will beep and yellow light will turn off.
How do you open a Honeywell with a dead battery?
Using A Honeywell Safe Key To access it, you must take the cover off of the safe’s batteries and remove the batteries. Insert your Honeywell safe key into the emergency keyhole and turn clockwise. At the same time, try to open the safe’s door. This should give you temporary access to your belongings.
How do I stop Honeywell from beeping?
How to stop beeping due to a problem with one or more zones: Press any key on the keypad to silence the trouble beep. Make sure that the displayed zone is intact. After the problem has been corrected, clear the CHECK or FAULT display by entering the OFF sequence (security code + OFF key) twice.
How do you reset a Honeywell door lock?
Factory Resetting a Honeywell Digital Deadbolt Remove one battery and wait 10 seconds. Put the battery back and wait until you hear a long and short beep. Within 3 seconds, press the Unlock button 3 times. The lock will beep and illuminate green via the light indicator, indicating that the process was successful.
How do I reset my electronic safe code?
Place the electronic digital safe into code reset mode. On some models you need to hold the last digit of the code or press the “*” button to get into code reset mode. Other safes require you to open them and press a small red button on the inside of the door.
Where is the model number on a Honeywell safe?
Identifying Your Honeywell Safe Model On the lower right-hand side of your safe, you’ll see the safe identification tag. This is typically a 16-character code that begins with two letters and then four groups of four digits, such as LP0000 1111 2222 3333.
Why is my Honeywell safe blinking red?
What does a RED blinking LED mean? A blinking red LED on these devices indicates that the main battery does not deliver power anymore. The device is running from its backup battery and is in critical suspend mode. Replace the main battery with a fully charged one to continue working.
Why won’t my sentry safe open with the key?
If the key doesn’t seem to open the Sentry Safe, it may have been turned in the wrong direction. Insert the Sentry key in the keyhole and turn it counter-clockwise as opposed to clockwise.
How do you stop a beeping safe?
Most standard systems will allow you to stop the beeping using one of the following methods: Disarm your system by entering your unique code. Arm your system and immediately disarm. Press the status button on your keypad.
How do you change the code on a Honeywell keypad?
How to change the master code of a Honeywell Alarm system Press 8 (the CODE key). Press 02. Enter a new four-digit master code. Re-enter the new code. The keypad will beep once to let you know that the code has been changed.
What does A and B mean on a safe?
A “yellow” light will come on indicating you can now reset your new code. 2) Input your new code and press “A or B” the safe will beep if the code has been accepted. However if the “yellow” light and the buzzer beeps 3 times the code is invalid and you will need to start again.
