Table of Contents
How often should I oil my chainsaw chain?
Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
Do you need to oil chain on chainsaw?
To run properly, all chainsaws need two types of oil for different jobs. The second type of oil, called bar and chain oil, is for lubricating the chain as it cuts. Choosing the correct oils for these two jobs and adding them to the tool correctly is crucial to the performance and longevity of your chainsaw.
Can I use 10w30 for chainsaw bar oil?
Normally, you would need to use bar and chain oil to lubricate your chainsaw because this type of oil was specifically formulated to be used on chainsaws. As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil.
Can I use wd40 as chainsaw oil?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
What can I use instead of chainsaw oil?
6 Chainsaw Bar & Chain Oil Alternatives Vegetable Oil. Vegetable oil is one of the safest alternatives available to oil your chainsaw. Canola Oil. Similar to vegetable oil, canola oil is another super-safe alternative. Motor Oil. Hydraulic Fluid (Diluted) Drained Motor Oil (Diluted) Drained Hydraulic Fluids (Diluted).
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated. Electric chain saws use the same type of lubrication for the bar and chain as gas-powered chain saws.
Can you use old motor oil for chainsaw bar?
Yes you can in a pinch, but motor oil is much thinner than bar oil and you will use it very fast. Chainsaw bar oil is thick and sticky and is designed to be used on bars and chains.
Can I use 2 stroke oil for chainsaw bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
What SAE is bar and chain oil?
To prevent this, chainsaw manufacturers make bar oils matched to the air temperature and the saw in which it is operated. Although they don’t disclose the weight of their oil, the University of Missouri Extension recommends in lieu of using a bar oil, select SAE 30 weight oil in summer and SAE 10 in winter.
How long can Gas sit in chainsaw?
Any more than 6 months and gas can start to go bad. Doesn’t mean it won’t run, but things start going bad. Stabil is good but it too has a shelf life of 2 years.
How tight should your chainsaw chain be?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
What happens to a chainsaw without bar oil?
No bar oil equals increased friction and heat. That adds up to a huge increase in chain and bar wear. Without bar oil, the chain teeth, drivers and links will all wear far more quickly. The increased friction can cause teeth to break.
Can I use olive oil for chainsaw?
Other vegetable oils most commonly used in chainsaws: Olive oil – thicker than canola but not good at low temperatures. Sunflower oil – thinner than regular chain oil.
Can I use vegetable oil instead of bar and chain oil?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
What weight is bar oil for a chainsaw?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
