Table of Contents
For Hardie siding, it’s recommended to use stainless steel or hot-dipped galvanized nails. You can either nail by hand or use a pneumatic nailer. However, it’s best to use a pneumatic nailer for speed and consistency. At the bottom, the siding should be face nailed, and at the top, it should be blind nailed.
Can you hammer a nail into Hardie board?
Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun. Don’t drive nails into the siding at an angle.
What nails do you use for Hardie siding?
NAIL TYPE: Fasteners must be corrosion resistant, galvanized or stainless steel. Electro-galvanized nails are acceptable for use with James Hardie Siding Products, but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.
How do you nail Hardie siding?
Fastening Siding Fiber cement siding can be nailed by hand or with a pneumatic nailer. It can also be attached using corrosion resistant screws. Use hot-dipped galvanized or stainless steel nails. Nails should penetrate through the sheathing and at least 1” into studs.
Do you nail or screw Hardie board?
What is the correct fastener pattern for installing HardieBacker® cement board? Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs.
What is the best way to fasten Hardie board?
Fasten the siding – You can fasten it with a pneumatic nailer or nailing by hand. You can use corrosion-resistant screws, or you can use stainless steel or hot-dipped galvanized nails. You can nail the siding by either blind nailing it at the top or face nailing it at the bottom.
How do you attach things to Hardie board?
Generally speaking, items can be attached to Hardie® siding by using either corrosion resistant nails or screws. The fasteners must be long enough to go through the siding and into wood or metal substrate (e.g. sheathing or studs).
What size nails do you use for Hardie board?
James Hardie recommends using stainless steel finish nails when installing HardieTrim products. Use a 2 in. finish nail to fasten trim together.
Can you use a framing nailer for Hardie siding?
With some overlap in nail size, you may wonder whether framing nailers can be used for siding? The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing.
Does Hardie board have to be nailed to studs?
GENERAL REQUIREMENTS: HardiePlank® lap siding can be installed over braced wood or steel studs spaced a maximum of 24″ o.c. or directly to minimum 7/16″ thick OSB sheathing. See General Fastening Requirements. Irregularities in framing and sheathing can mirror through the finished application.
Can a roofing nailer be used for siding?
You can’t fire roofing nails from a siding nailer or vice versa, so it’s important to make sure you’re using the right fastener and therefore the right nailer for the job.
Can you use screws on Hardie board?
HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel. Fasteners shall be installed between 1 in. and 3/4 in.
Will command strips stick to Hardie board?
They will stick to the hardiplank but I don’t think the adhesive will hold after rain, unless it’s under a shed of some sort. 1 of 1 found this helpful.
What kind of screws are used for Hardie board?
James Hardie recommends 1-1/4” long galvanized or STAINLESS steel roofing nails or 1-1/4” long ribbed waferhead screws in compliance with the tile industry. It is 8-18 x 3/8” HD.
What is a 6d nail?
Answer: A 6d nail is 2 inches long. Note: The “d” means “penny.” For example, a 10d nail is a 10-penny nail. The nail sizes go up ¼-inch (1.905 cm) for each penny. A 7-penny nail is 2¼ inches (5.715 cm) long.
Can I use a roofing nailer for Hardie siding?
You can shoot Hardie siding on with air powered nailers or use hand driven roofing nails to attach siding to the home or structure. The nails can be ringed- shanked or smooth just make sure you are hitting the studs in the wall. Our Crews prefer 1 3/4 “ smooth shank roofing nails for Hardie installation.
How long should nails be for siding?
Most contractors agree that nails used in siding projects should measure at least 1 ½ inches long—or up to 2 ½ inches if you’re installing backerboard with the siding.
Can I use a brad nailer for siding?
A pneumatic nail gun should be used for siding installation, especially for harder fiber cement siding. You cannot use a brad gun for installing siding because the brads leave two holes for each brad and do not hold up as well as siding nails.
Are roofing nails the same as siding nails?
Just remember that siding nails and roofing nails are not the same, and they cannot be used in place of one or the other. In most situations, you want separate nails for the two separate tasks. This way you’re ensured that you get the siding installed correctly the first time.
