Table of Contents
For Hardie siding, it’s recommended to use stainless steel or hot-dipped galvanized nails. You can either nail by hand or use a pneumatic nailer. However, it’s best to use a pneumatic nailer for speed and consistency. At the bottom, the siding should be face nailed, and at the top, it should be blind nailed.
Can you hammer a nail into Hardie board?
Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun. Don’t drive nails into the siding at an angle.
What kind of nails do you use on Hardie board?
James Hardie recommends the use of quality, hot-dipped galvanized nails. James Hardie is not responsible for the corrosion resistance of fasteners. Stainless steel fasteners are recommended when installing James Hardie® products near the ocean, large bodies of water, or in very humid climates. Min.
Do you nail or screw Hardie board?
What is the correct fastener pattern for installing HardieBacker® cement board? Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs.
How do you attach things to Hardie board?
Generally speaking, items can be attached to Hardie® siding by using either corrosion resistant nails or screws. The fasteners must be long enough to go through the siding and into wood or metal substrate (e.g. sheathing or studs).
What size nails do you use for Hardie siding?
James Hardie recommends using stainless steel finish nails when installing HardieTrim products. Use a 2 in. finish nail to fasten trim together.
Can you hand nail Hardie siding?
You can shoot Hardie siding on with air powered nailers or use hand driven roofing nails to attach siding to the home or structure. The nails can be ringed- shanked or smooth just make sure you are hitting the studs in the wall. Nails drive in too high won’t hold as won’t nails that are over driven.
Do you need to put Thinset under Hardie board?
However, many manufacturers including, both Durock and Hardiebacker not only recommend that you use thinset under their backerboard, but they specify it and will void the warranty on their product if it’s not used. Thinset is going to create a solid surface under tile and prevent flexing that could lead to cracking.
Does Hardie siding need to be nailed to studs?
GENERAL REQUIREMENTS: HardiePlank® lap siding can be installed over braced wood or steel studs spaced a maximum of 24″ o.c. or directly to minimum 7/16″ thick OSB sheathing. See General Fastening Requirements. Irregularities in framing and sheathing can mirror through the finished application.
Can you screw into Hardie board siding?
HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel. Fasteners shall be installed between 1 in. and 3/4 in.
Will command strips stick to Hardie board?
They will stick to the hardiplank but I don’t think the adhesive will hold after rain, unless it’s under a shed of some sort. 1 of 1 found this helpful.
Can you use a framing nailer for Hardie siding?
With some overlap in nail size, you may wonder whether framing nailers can be used for siding? The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing.
What is the best nail gun for Hardie siding?
Our Top 4 Picks for the best nail gun for James Hardie siding Best James Hardie Siding Nail Gun Overall: BOSTITCH Coil Siding Nailer. Runner-Up: Makita Nail Gun Hardie Siding Coil Nailer 2-1/2″, Silver. Best Hardieplank Nailer Budget: Freeman Pneumatic 15-Degree 2-1/2” Coil Siding Nailer.
What is the difference between blind nailing and face nailing?
While the majority part is blind nailed, you face nail the very last row of your floorboards since you cannot reach the groove (of tongue-and-groove flooring) by blind nailing. Other than that, face nailing will not make the tongue and groove tight as intended.
Should Hardie board be caulked?
APPLICATION: General: James Hardie believes it is good building practice to seal the joints to prevent moisture, such as wind-driven rain and snow, from penetrating the wall cavity. Caulking around windows, doors, eaves and trim edges gives added insurance that leaks will not occur.
How do you attach cement board?
Drill a small hole in one end of a scrap of wood, attach it to the cement board at the center of the circle, screwing through the cement board into the work surface below. Then screw in a “cutter” screw where you want the circle to be scored, for example, 2 in. from the center for a 4-in. hole.
Can a roofing nailer be used for siding?
You can’t fire roofing nails from a siding nailer or vice versa, so it’s important to make sure you’re using the right fastener and therefore the right nailer for the job.
What happens if you don’t put thinset under Hardibacker?
It will make an enormous mess under the house (or whatever is under your bathroom). It is also more likely to make the floor uneven since it is hard to level thinset that is separated by gaps. The installation manual for HardieBacker suggests to embed it in thin-set and it should be installed over plywood.
