Table of Contents
Instructions Remove the Toilet. Remove the toilet from its current location. Gain Access. Remove the Toilet Flange. Cut the Toilet Bend. Position the New Drain Location. Run the New Drain. Install the Drain Stub-Out. Run the Water Supply Lines.
How difficult is it to move a toilet location?
Moving a toilet is not a straightforward weekend DIY job, but it is very doable when you involve the professionals. Once the toilet itself is removed, your plumber will have to move the drainage, as well as the water supply to accommodate the new location.
How much does it cost to relocate a toilet?
The cost to move a toilet or sinks can be $2,500-$3,500 per fixture. Plumbing can be a significant cost factor in a remodel when a bathroom floor plan is altered. The toilet is the most expensive to move. Connecting the toilet to the existing sewer line can be a bit tricky for your plumber.
How far can you relocate a toilet?
If your waste line has a diameter of 3 inches, you can place the toilet within six feet of your stack. The toilet can also be as far as 10 feet from your stack, if the diameter of the waste line is 4 inches.
Can you put a toilet anywhere in your house?
On a serious note, it is absolutely possible to install a toilet, even a bathroom as a matter of fact, anywhere in your house. In the past, many homeowners have had the idea of their dream bathroom crushed because the location was simply too far away from the main drain.
How do you relocate a toilet?
How to Move a Toilet in 8 Simple Steps Make a plan. Make space for the toilet before you move it. Turn off the water. Remove remaining water. Disconnect the supply line from the toilet. Remove the bolts. Remove and move the tank. Remove and move the toilet bowl. Clean and plug the drain hole.
How far can you move a toilet with an offset flange?
For the waste water line, an offset toilet flange will allow you to move the toilet a couple of inches in any direction without having to cut a new hole in the floor or reconstruct the waste water pipe.
How much does it cost to move a toilet on a slab?
Although the cost of the toilet itself is not nearly as much as a tub or shower, the expensive part is the pipes. Just running the pipes is typically about $1,500 to $3,500.Moving the Toilet. Brand Cost Saniflo $300 to $1,200.
How expensive is it to move plumbing in a bathroom?
On average, it costs somewhere between $500-$1,000 to move a plumbing fixture around three feet or more. This varies, of course, depending on if your plumber needs to move anything around to connect to your drain, vent, or water lines.
Can you move a toilet to where a shower was?
Can you put a toilet where a shower was? The simple answer is yes, you can put a toilet where a shower was, but the move doesn’t come without its issues. This isn’t a simple DIY job. You are going to have to remove at least one wall and, hopefully, only a small portion of the floor.
How much does it cost to move a toilet Australia?
Every property in Australia is unique so the cost to move a toilet can vary from $100 to many $1,000’s depending on the property type & layout. What will vary greatly is the time, tools and materials needed to complete any type of toilet move whether that is a wooden floor board or concrete slab.
How far is toilet from wall?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
Can you have a toilet without plumbing?
A Saniflo is normally installed in a domestic property where there is no mains drainage pipe available. This means you can have a toilet anywhere, without worrying about mains drainage. You could install a downstairs toilet under your stairs, create an ensuite bathroom or even install a toilet in your basement.
Do you need planning permission to add a toilet?
Usually, adding a downstairs toilet to your home does not require planning permission, unless it is part of a larger extension. Speak to your planning consultants and they can advise you on where you stand with planning permissions. Your new toilet will have to adhere to building regulations.
Can you move plumbing in a bathroom?
While it’s possible to move almost any large fixture, beneath the bathroom floor are supporting joists that you should not cut in order to install new drains. Design your new configuration so that the new drainpipes run parallel to the joists and between them.
How do you move a toilet drain pipe?
Is it OK to use an offset toilet flange?
Yes, all offset flanges will affect the flow somewhat, some drastically. A company named Sioux Chief makes one that I would not hesitate to use on my own home, called a Full Flush, part #889-POM (PVC) or 889-AOM (ABS).
Are offset flanges against code?
Offset flanges may or, not be illegal under the code used in your area. I don’t know your code. They may not be the best practice and should be avoided if possible.
What is the purpose of an offset toilet flange?
Unlike a standard flange, which is centered on the waste pipe, an offset flange is off-center—that lets you shift the location of the toilet by a couple of inches (left, right, forward or back). P.S. Flanges with stainless steel rings cost a few bucks more than all-plastic versions.
How do you install a toilet on a concrete floor?
Installing a Toilet on a Concrete Floor Step 1: Place the Flange. Place the toilet flange face down on the concrete. Step 2: Drill Holes for the Flange. Step 3: Clean the Area. Step 4: Attach the Flange. Step 5: Finish the Flange Installation. Step 6: Connect the Toilet.
How much does it cost to cut concrete for plumbing?
Concrete Cutting Costs Per Foot Pros usually charge between $4.75 and $7.50 per linear foot to cut a typical 4 inch slab. The final price can change depending on the complexity of the job, as well as regional labor and material costs.
