Table of Contents
How do you cut a latch plate mortise?
How do you cut a door mortise?
Mark the hinge outline. Place the hinge on the edge of the door with the knuckles pointing in the direction the door opens and mark around its perimeter with a pencil. Mark the mortise depth. Hold the edge of the hinge against the bit’s lower edge. Drill the mortise. Trim the waste. Test the fit.
How do you fill a mortise lock hole?
Apply glue to the interior of the hole. Tap the dowel plug into the hole as far as possible, aligning the grain pattern of the dowel rod vertically. Allow the glue to dry overnight. Force wood filler into any seams around the perimeter of the patch.
Do you have to mortise door hinges?
Doors must be mortised to make hinges fit properly. It allows the hinge to fit flat and flush with the edge of the door inside a shallow cut. Production door shops use routers and jigs to cut mortises, but you can do single doors by hand with a hammer and chisel.
What size hole do I drill for door latch?
The standard sized bore hole is 2 1/8″ in diameter. Through the edge of the door there is a 1″ cross bore that extends from the edge of the door through the bore hole. This cross bore is where the latch is installed. In addition to the two cross bores, a door can be prepped for one of 3 different types of latches.
Does the trend lock jig Do latches?
Trend Lock Jig – Fast accurate jig for fitting mortice locks and latches to internal, external and fire doors using a 1/2in router.
What is a 5 point Mortice lock?
The five lever mortice deadlock is a type of door lock commonly fitted to wooden doors. It can be locked and unlocked with a key from both the inside and the outside. It works by inserting and turning the key to move the five levers into the correct position, allowing the bolt to be locked or unlocked.
What is a half mortise hinge?
Half surface door hinges — also called half mortise hinges — have one leaf mortised into the door jamb and the other leaf mounted on the door surface. Available in solid brass with a wide selection of finishes to perfectly match your home’s decor.
How do you make a strike plate hole bigger?
You can move the strike plate up or down and in or out. Use a sharp chisel to enlarge the strike plate mortise. Then hold the strike plate in place and drill new 1/16-in. holes for the screws.
How do non mortise hinges work?
The Horton Brasses non-mortise hinges are engineered for a 3/32” gap-the standard for fine cabinetry. Nesting each leaf together creates a thin profile. This is what allows you to get by without cutting any mortises. In fact, it provides the perfect gap (about 1⁄16″) where the door meets the cabinet.
What is full mortise hinge?
A full mortise hinge is a plate hinge designed to have one or both leaves mortised into the door and the cabinet face or door jamb. The hinge sits flush with the surface of the door and frame when installed, leaving a smooth finished appearance.
What is a latch bore?
The latch bore, also known as the edge bore, is the hole drilled from the side of the door into the cross bore to allow the latch of the lock to be installed and to accommodate the sliding of the deadbolt. The diameter of the latch bore is generally 1” to accommodate bolts from either mechanical or electronic locksets.
Can I mortise with a router?
If you own a plunge router you can use it to cut mortises with flat and straight side walls requiring no cleanup. However, the mortise ends will be round, meaning you have to either square them with a chisel or use a “floating” tenon with rounded edges that fit into two identical, mating mortises.
What tools do I need to make a mortise and tenon joint?
If you’re doing woodworking on a shoestring budget, you’ll be happy to know that the only tools you need to cut tight-fitting mortise and tenon joints are a square, knife and marking gauge, a fine-toothed saw, and a couple of sharp chisels and mallet.
What is the best hinge jig?
Top 8 Best Door Hinge Mortise Jigs Reviews Ryobi A99HT2 Door Hinge Installation Jig – Best Door Hinge Mortise Jigs. PORTER-CABLE Door Hinge Jig Template – Best Hinge Template Kit. Trend H/JIG/C 2-Piece Hinge Jig Skeleton – Best Full Length Door Hinge Template.
How does a plunge router work?
Plunge Routers Go Where No Other Router Can. A lock/release lever allows free up-and-down movement of the router housing or locks it in place at a given depth. The depth of cut can be preset, allowing you to position the router over the work and plunge the bit to an exact depth.
What is a Dremel used for?
Dremel rotary tools are suitable for carving, engraving, routing, grinding, sharpening, cleaning, polishing, cutting and sanding. Many different accessories and attachments are also produced. Dremel Multitools work by using speed instead of torque.
What is the best Mortice lock?
ASEC 5 Lever BS3621 Mortice Locks The ASEC 5 lever BS3621 Deadlock and Sashlock are probably the most cost-effective lock on the market. They are a copy of the Legge lock range that has now been discontinued but with these ASEC locks available you don’t need the Legge range.
What is the difference between a deadlock and a mortice lock?
The difference between a mortice deadlock and sash lock is that a mortice sashlock has a latch and bolt to open and close the lock. Where-as a mortice deadlock does not have a latch to open the lock.
How secure is a mortice lock?
Mortice locks are generally stronger and secure than a bored cylindrical lock. Ironically, installing a Mortice Lock initially can weaken the structure of a typical wooden door, but by choosing a 5 lever Mortice Lock your home will be more secure.
How long does it take to install a mortice lock?
Resolution: Typical installation by an experienced Schlage L lock installer on a door correctly prepped for the Schlage L-Series function could take 10 to 20 minutes.
