Table of Contents
To measure the rough-in for your toilet, measure from the wall behind to the toilet to the middle of the closet bolt caps on your current toilet. The closet bolts are the bolts holding your toilet to the floor. If you have baseboards or tiling on the wall behind the toilet, do not include those in your measurement.
How do I know if my toilet is a 10 or 12 rough?
If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 11.5 and 12.5 inches, it is a 12-inch rough-in.
Can you replace a 10-inch rough-in toilet with a 12-inch rough-in toilet?
The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.
Can you replace a 14 inch rough-in toilet with a 12-inch rough-in toilet?
You can, but the back of the toilet tank will be two inches further away from the wall. The “rough-in” dimension refers to the distance from the wall framing (½-⅝″ behind the finished wall surface) to the center of the sewer pipe on the floor. Standard rough-in is 12 inches.
What does 12-inch rough-in size mean for toilets?
The toilet rough-in refers to the distance from the finished wall to the center of the toilet’s floor drain or waste outlet. Most toilets have a rough-in of 12 inches, although it’s not uncommon for older homes to have an unusual size such as 10″ or 14″. Rear-outlet toilets are configured a bit differently.
How do I know what size toilet to buy?
To measure the bowl shape, you can start by putting your measuring tape at the back of the toilet, and extend the tape forward to the end of the bowl, measuring parallel to the floor. The most important measurement you can take for a replacement toilet is the rough-in dimension.
What is standard rough-in size for toilet?
The standard rough-in is 12 inches, though you may encounter 10-inch and 14-inch rough-ins in older homes. You should find the rough-in measurement in the new toilet’s product information.
How far from the wall should a toilet rough-in Be?
The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall.
Why would I want an elongated toilet bowl?
Elongated bowls are also considered more ‘hygienic’ in that the larger surface area of the bowl makes is easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.
How far from the wall does a toilet need to be?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
How many inches does an offset toilet flange move?
The typical offset is 12-inches for most residential toilets. As a result, the toilet had 4-inches behind the tank. It looked like it was trying to participate in the activities of the bathroom rather than sit quietly until needed.
What is the difference between a 12 and 14 rough-in toilet?
The main difference between 12-inch rough-ins and 14-inch rough-ins is in their size (proportions). Depending on the type of bathroom, 12-inch rough-ins are generally more used than 14-inch rough-ins, but they both have merits, which means that you sometimes need to reduce the space from behind the tank.
Can you replace a 13 inch rough-in toilet with a 12-inch rough-in toilet?
That’ll be your rough-in. If your distance if 13″ and you have a 1″ gap between the tank and the wall, then yes, your existing toilet is probably a 12″ toilet. You can indeed have two 12′ toilets that differ in size from one another.
Are 1 piece toilets better?
One piece toilets are typically heavier and easier to clean, and there’s less space for bacteria to grow. Because two piece toilets feature a detachable tank, they’re more customizable for preferred styles and heights. Both styles can include bells and whistles like bidet attachments or low-flow energy saving.
What does 10-inch rough-in toilet mean?
When you wonder about ‘what a 10-inch rough-in toilet means’, it refers to the finished wall and the floor flange opening center distance of about 10-inches. 10-inch rough-in is usually found in the old models’ homes. Although, there are only fewer toilets options available.
Do toilets come in different sizes?
Are there different sizes of toilet? Yes, toilets come in a range of different sizes, that’s why it’s important to measure your existing toilet seat before you buy.
How often should you replace your toilets?
Typically, toilets need replacement after 25 years of use so this can be considered the average toilet lifespan. Some would argue that the porcelain toilet itself has a much longer, and even unlimited, lifespan and that it’s only the components inside that need repairs and replacements.
Which is better round or elongated toilet?
Most people find elongated toilet bowls to be more comfortable, but in a small bathroom, a round bowl can save space. Elongated toilet bowls measure up to 31″ from the wall, while round fixtures max out at 28″. Because round bowls are less expensive than elongated bowls, they save a few dollars, too.
