Table of Contents
Choose a stair rise somewhere between 7 and 7-1/2 inches. Take your total height divided by that stair rise number. This will almost always give you a long decimal number. Round to the nearest whole number – this will be the number of steps you will have in your staircase.
How do you measure the length of a stringer?
How to Calculate Stair Stringer Length Measure the height from the surface where the stairs will start to the bottom surface that the stairs will connect to. Divide the height of the staircase in inches by the intended rise of each step, also in inches, to assist in determining the stair stringer length.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
How do I calculate how many steps I need for stairs?
Divide the rise by 6 or 7 inches (15 or 18 cm) to find the total number of stairs. For larger stairs, divide by 6 and for smaller stairs, divide by 7. The total you get is how many stairs your future staircase will have so you can plan accordingly.
How do I calculate how many steps I need?
You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
How do you calculate stair landing?
The height of the landing is determined by where it is located along the stair run. In this design, since it is half way from the top level, it is 8 steps high (8 x height of each step (6 7/8) equals 55 inches). The horizontal positioning of the mid-level landing is determined by the number of treads on the stair run.
How many steps is 12 feet?
For example, suppose your height of ceiling is 12 feet high, generally you will need 20 stairs or steps to go up (12 × 12 ÷ 7 = 20). Formula for number of stairs or steps = total height × 12 ÷ 7 or height of staircase/ height of one riser.
How many steps are in 10 feet?
Length of Staircase for a 10 Foot Ceiling A staircase in a home with 10′ ceilings requires 17 steps. Stairs that have a tread depth of 11” will have a total length of 187”. Stairs with a tread depth of 10” will have a total length of 170”, which is the minimum length.
Can I use 2×8 for stair stringers?
You should attach 2×6 or 2×8 support framing under the rim flush to the bottom of the stringer. The stairs will hang here. Install a piece of blocking below the rim joist to extend the attachment surface for your stairs stringers. Use a level to mark the top step.
What size board do I need for stair stringer?
Stringers should always be cut from 2x12s. Notching smaller stock doesn’t leave enough wood to safely carry the loads of a stair. When ordering stringers, allow about 14 inches of stringer length for each step. Look for straight stock with as few knots as possible.
How far can a 2×12 stair stringer span?
A 2×12 stringer has a maximum unsupported span of 6 feet. These stairs (7) are likely to deflect and cause the stringers to either pull loose from the framing or shear along the grain.
How do I calculate my step distance?
If you want to calculate your walking stride length, divide the number of steps you took by 2 and divide that number into the measured distance. If it took you 16 steps to cover 20 feet, divide the number of steps (16) by 2 to get the number of strides. Then take the answer (8) and divide it into the distance.
How do I calculate my walking steps?
Photo: Pedometers can measure your steps because your body swings from side to side as you walk. Each swing counts as one step. Multiplying the number of “swings” by the average length of your steps tells you how far you’ve gone.
How do I measure my foot for walking?
Walk at a normal speed from one end of the course to the other, counting your steps as you go. Divide the total number of steps into 100, and you’ll find out the length of one step. For example, if you took 50 steps to go 100 feet, your step length is 2 feet. If it took you 40 steps, figure 2 1/2 feet per step.
How many stair stringers do I need?
If cut stringers are used in the stair construction, then at least three stringers are required. Cut stringers should be spaced no more than 18 inches on center. For example, a 36-inch-wide stairway should have three stringers. If the stairway is wider than 36 inches, four stringers should be installed.
How tall is a 5 step Stringer?
Stair Stringer-5 step Redwood (Common: 60 in. x 11 in.; Actual: 1.5 in. x 11 in. x 60 in.).
Does the landing count as a step?
Does the landing count as a step? Yes it does. It amazes me how many people like to argue this one. Remember that when counting stairs, you are counting how many times you have to lift your foot.
How many steps is 4 feet?
A four-foot high deck can have a range between 6 and 8 steps.
