Table of Contents
Start by measuring the rough-in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. It’s best to perform this measurement before you remove the old toilet.
How do you measure a 10-inch or 12-inch rough-in for a toilet?
Take the cover off of the toilet tank, and lay the toilet on its side to access the underside of the base. Measure from the back edge of the base to the center of the closet hole, or drain hole. Note if the measurement is 10 inches or 12 inches.
What does 12-inch rough-in mean?
The toilet rough-in refers to the distance from the finished wall to the center of the toilet’s floor drain or waste outlet. Most toilets have a rough-in of 12 inches, although it’s not uncommon for older homes to have an unusual size such as 10″ or 14″.
How do you know the rough-in for a toilet?
The rough-in measurement of a toilet refers to the span between the wall behind the toilet and the center of the waste pipe. To measure the rough-in for your toilet, measure from the wall behind the toilet to the middle of the bolt caps (the caps holding your toilet to the floor).
What are rough in dimensions?
Start by measuring the rough-in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. It’s best to perform this measurement before you remove the old toilet.
Can you replace a 10-inch rough in toilet with a 12-inch?
The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.
How do you measure a rough-in corner for a toilet?
To determine the toilet rough-in location, measure and mark the rough-in length out from the corner on each wall. For this example, a toilet with a 12″ rough-in was used. 2. Use a straight edge to draw two perpendicular lines from the marks created in the previous step.
Can you put a 12-inch rough-in toilet on a 14 inch rough-in?
Terry Administrator Staff Member. Any 12″ toilet will work for a 14″ rough. If you want to pull the bowl back 2″, then there is only one method.
Can you replace a 14 inch rough-in toilet with a 12-inch rough-in toilet?
Replace a 14-inch rough-in toilet with a 12-inch rough-in toilet. You can definitely replace a toilet with a rough-in of 14 inches with one with a rough of 12 inches. The problem with this method is that a 2-inch gap will be left between the toilet tank and the wall. Install an offset toilet flange.
What does rough in mean?
: to make a rough or unfinished version of (something, such as a design) as the first step in creating the finished version Rough in the lettering on your poster. He roughed in the frame of the new door.
How far is toilet rough in from wall?
The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing. Minimum distance in front of the toilet to the facing wall or fixture is 21 inches.
How far does a toilet stick out from the wall?
In general, round-front toilets extend 25 to 28 inches from the wall. Elongated toilets extend 29 to 31 inches. Because the toilet sits opposite the door in many smaller bathrooms, a regular elongated toilet can restrict the size of the door or its swing.
Do all toilets fit the same?
For a standard toilet, the rough-in measurement should be between 11 inches and 13 inches. If the rough-in measurement is not between 11 inches and 13 inches, a standard toilet will not fit the space, and you will need to look for a toilet designed for that specific rough-in distance.
How do I know what kind of toilet I have?
The number: Look under the water tank lid (on the bottom), or on the inside walls of the tank. * The number on the lid may or may not be the same as the in the tank or the number of the complete toilet model.
What is the rough-in for a standard tub?
The standard rough-in dimension for a bathtub is 60-¼”. But if there’s a gap, you can attach furring strips to the stud wall. You can also apply some cement or plywood.
What is a roughed in bathroom basement?
A plumbing rough-in means that all water supply and drain pipes have been run through bored holes in the studs and other framing members and that all pipe connections have been made. A roughed-in bathroom or kitchen typically has capped PEX or copper water supply pipes jutting up through the floor or wall.
What is the rough opening for a standard tub?
Hope this helps! Standard rough opening for a 60″ tub is always 60-1/4″. Joe Carola, Rough openings are not always framed in 1/4″ over the size of the fixture.
Can you use a 12 inch rough in toilet?
12 Inch Rough In Toilet A 12 inch rough in is the most common measurement in bathrooms. This size allows for the most variety in the shape of the bowl and style of the toilet you purchase. Even though this is the most standard measurement, don’t forgo measuring (at least twice) before buying a new toilet.
Can you move a toilet over a few inches?
Yes, you can actually move a toilet. Even moving a toilet by a few inches without having to make a new hole in the floor is possible. You can use an offset toilet flange to move the toilet by a couple of inches on any side. This will allow you to use the same wastewater line and in turn help to save you a lot of money.
Are all toilets 12 inches from wall?
Toilet Rough In Dimensions: A toilet’s rough-in measurement is the space between the wall behind the toilet and the center of the waste pipe. Standard toilet rough in dimensions are 12 inches but can be anywhere from 10 to 14 inches in some cases.
Can you angle a toilet in a corner?
By placing it at an angle, the user will have plenty of leg space and the sink will not be in their way. Notice that the toilet is designed to fit in a corner.
Do corner toilets save space?
Do corner toilets really save space? Yes! The toilet tank is typically smaller, and shaped like a triangle to allow the toilet to fit into a corner space of a bathroom. Space that is normally wasted.
