Table of Contents
Measure the actual mower deck size using a tape measurer and extend the tape from the widest point on one side of the deck to the opposite side of the deck. The average riding lawn mower, also referred to as a garden tractor, is between 48 inches and 63 inches wide with the discharge chute in the upright position.
What size belt do I need for a 42 inch deck?
There’s no standard size for a 42-inch-cut riding mower. Each model uses a different size belt. To give examples, some models use a drive belt that is ½ inch wide by 92 inches in length, while others use a belt ½ inch wide by 85 inches in length.
How are John Deere mower decks measured?
Lie down on the ground next to the elevated mower, and pass the tape measure beneath the blades, hooking it on the opposite side of the deck. Note the distance on the tape measure. This is your deck size.
How do you measure for a riding lawn mower cover?
How to Measure a Riding Mower Deck Run the measuring tape over the top of the mower deck, from right to left or left to right, as close to the middle as possible. Secure the end of the measuring tape on the other end of the mower deck and note the size.
What does the inches mean on a lawn mower?
The smaller your yard, the smaller the mower deck can be – the actual width the mower will cut in a single pass. A 20-inch walk-behind mower may be perfect for a small yard, but you will probably want a 21-22 inch mower for a larger yard to cut down on mowing time.
What causes a mower deck belt to come off?
A riding mower belt can come off your mower when brackets, belt keepers or idler spring are worn or damaged; your bearings are bad in your pulleys or spindle housings; or debris is interfering with the tension of your deck belt. You will be able to repair your problem and not have to keep reinstalling your belt.
Can I put a bigger deck on my mower?
Can I put a bigger deck on my mower? Yes, you can fit a bigger deck to your mower, but engine power and deck size are often proportional.
What is lawn mower deck size?
Deck widths range from 42 inches to 54 inches. To know what size you need, divide the mower deck size by 12 to get an approximation of the acreage the mower can handle. So residential-duty a mower with a 54-inch deck can mow up to 4.5 acres.
What size mower do I need for 1/2 acre?
For lawns over 1/2 acre, we recommend upgrading to a riding mower. If cutting time is important and you have a lot to cut, you need a fast riding mower with a 40-60 inch+ cutting deck.
What is the deck on a riding lawn mower?
A lawn mower deck is the part of a lawn mower that protects the user as well as the engine of the mower from the blades and the debris shot off from the blades.
Is there such a thing as a lawn mower cover?
DURABLE – Heavy Duty, Tear Resistant Push Mower Cover saves your equipment from rain, snow, sun, leaves, pine sap, pollen, dust, dirt, wind and birds. EASY TO USE – Draw cord at bottom assures a tight fit around the complete lawn mower for full protection.
Where is the model number on a John Deere mower deck?
Model & Serial Number Location The model serial number of a John Deere lawn mower is printed on an identification tag located on the left side of the deck (standing behind the mower). The serial number (PIN) is 13 or 17 digits long.
What size of mower do I need?
Choosing by Lawn Size Lawn size in meter square Recommended Mower size (cutting width in cm) 0-250 30-34 100-250 35-39 100-500 40-44 Push mower 250-750 40-44 Self Propelled mower.
What is the difference between 16 inch and 20 inch lawn mower?
For most people, you have to overlap cuts by roughly two inches to avoid that line of tall grass you missed here and there. That means a 20 inch mower effectively covers 18 inches per pass, while a 16 inch mower covers 14 inches. To mow your lawn you would have to walk 28% farther with the smaller mower.
How long should a mower deck belt last?
Good mower belts should last for about 3- 4 years. If you don’t have a quality mower belt, you need to get one to use it for this long. As you use a mower belt, you should also inspect it from time to time to confirm any signs of tear.
Can a lawn mower belt stretch?
Yes, lawnmower belts can stretch. Continuous wear due to regular operation can cause them to elongate over time. When it stretches more than it should, it can result in the drive belts lose grip on the pulley system. Take note that some mowers rely on pulley systems to cut grass.
How do I know what size deck belt I need?
Continue to measure around the inside of the lawnmower deck until you record the distance between the last spindle pulley and Spindle Pulley 1. Add up the measurements to determine the total distance around the spindle pulleys. This is the size of the mower deck belt you need.
What size belt goes on a 48 inch deck?
Husqvarna Deck Drive Belt fits 48″ Cut Decks No. Size: 5/8″ x 152″.
What is the difference between a deck belt and drive belt?
So, with the mower deck removed from the tractor, the “drive belt” would be the one still on the tractor. The mower deck itself will still have the internal “deck belt” which if you turn one blade by hand, all blades turn because that deck belt is what connects and drives all the blades together.
