Table of Contents
Overlay refers to how much the door overlaps on the hinge side. You can determine this by measuring the width of the door, subtract the width of the opening and divide that in half. For example, if the door is 1” wider than the opening, that means it overlays 1/2″ on each side, so you would select 1/2″ overlay hinges.
How do you size a full overlay cabinet door?
To measure for full overlay cabinet doors on frameless cabinets, the cabinet door needs to be 1/8″ smaller than the cabinet on all sides. So first take a measurement of the cabinet opening, then subtract 1/8″ on all sides.
How much does a full overlay cabinet door reveal?
A Full Overlay door will overlay that same 1.5” face frame 1.25”, leaving a ¼” reveal on the sides (stiles) and bottom (rail).
How do you determine cabinet door size?
Add 1 inch to both the width and the height of each opening size measurement. For example, a 14″ x 30″ cabinet opening should now read 15″ x 31″. This technique allows for a 1/2″ overlay of cabinet door openings. If you order by cabinet order size alone, your doors will be too small.
How much larger should a cabinet door be than the opening?
Add space for door overlay: Cabinet doors for framed cabinets must be larger than the cabinet opening to look right and close properly. We refer to this as an “overlay”. The industry standard for most cabinet doors is a 1/2 inch overlay around the cabinet door.
How do you calculate door overlay?
Another way to look at door overlay: If your door is 30″ wide and the opening is 28″ wide then then you could calculate your overlay as 30 minus 28 divided by 2 equals 1″. Divided by two because the overlay is measured on one edge, the hinged edge of the door.
What does 1/2 inch overlay hinge mean?
1/2″ overlay hinges are the most common overlay of cabinet hinge. These are used in face frame cabinets where the door covers a 1/2″ of the face frame all the way around the cabinet door. These are used in face frame cabinets where the door covers a 1/2″ of the face frame all the way around the cabinet door.
What does 1 2 inch overlay mean?
A 1/2″ overlay literally means that all the drawers and doors of a cabinet run will extend half an inch over the frame. This is a classic styling for cabinetry and leaves about two inches of exposed frame in between cabinet doors.
Are full overlay cabinets more expensive?
Lower Cost: Full overlay cabinets take less skill to install and are therefore less expensive. More Storage: Because the doors are mounted on the face frame instead of inside it, there’s more room to squeeze large items through the opening than in inset cabinets.
What is the reveal on a cabinet door?
Door reveal refers to the portion of a cabinet frame left exposed after the door is attached. The size of your reveal is determined by the size of your doors in relation to your cabinet case frame.
What is a standard overlay hinge?
The door “overlay”, is how far the actual door overlaps the face frame of the cabinet. Typically most cabinets (even cabinets built with exposed hinges) will stay true to the ½” overlay standard.
Is it possible to just replace cabinet doors?
You can definitely just replace cabinet doors. If you’re up for a little bit of work with some basic tools, and maybe a spare set of hands to help, you can even do it yourself.
Do cabinet doors come in standard sizes?
What is the standard size of kitchen cabinet doors? Kitchen cabinet door heights are typically between 24 and 30 inches. If the base cabinet features a drawer, the door height below it the drawer is typically 24 inches.
What are standard cabinet door sizes?
Width- 12-36 inches. Standard width for a single or double door wall cabinet is generally available in widths from 9″ to 36″, we carry them in increments of 3″ (i.e., 9″, 12″, 15″).
How do you measure for cabinets?
Start from an adjoining corner of the wall and work clockwise, taking horizontal measurements of the wall at 36-inch height. Measure from one edge of the wall to the other, skipping over any windows, appliances, or fixtures. Label each of the walls with a number for easy reference.
What is standard cabinet overlay?
Standard overlay cabinets (also called traditional overlay) tend to be less expensive and do not require hardware because there is enough finger space on the side of the cabinet door or drawer face. They also have more exposed face frame, with at least 1 ¼ inches on all sides of the doors and drawers.
How should cabinet doors open?
Placed horizontally: You could center them 2″ to 4″ from the bottom of the door and about 2″ from the side edge of the door. Placed Vertically: They can be centered on the side ‘rail’ of the cabinet that runs verticallyand about 2″ from the side edge of the door.
What is door overlay?
When referring to an overlay door, it means the entire door lays on top of the cabinet frame. Overlays can come in a variety of sizes but in common applications we most often see a 1/2″ overlay or 1/4″ overlay. The above photo shows the entire door is on the outside of the cabinet frame. This is an overlay door.
How do you measure overlay on a double demountable hinge?
Open the cabinet door and measure from the inside edge of the tape near the opening. You can also draw a faint line on the face frame with the edge of the door as the straight edge. Measure from the line to the edge of the opening to determine the overlay.
What is overlay depth hinge?
The overlay is the amount or distance that the cabinet door overlaps the cabinet opening on the hinge side of the door. Normally, this distance is the same on both sides of the cabinet opening and will range from 3/8″ to 1-9/16″.
What does half overlay mean?
Half overlay is a reference to a particular measurement that allows for doors and drawers to be placed so they reveal dividing strips of the front face frame, but it can reference a particular characteristic associated with Euro box cabinets too.
How are hinges measured?
The first way to measure a hinge’s width is to completely open the hinge on a flat surface. Stretch your ruler or measuring tape over the hinge and measure the edge of one leaf to the edge of the other. Unlike measuring leaf width, the measurement includes the pin and knuckle joint in the middle.
