Table of Contents
Choose a stair rise somewhere between 7 and 7-1/2 inches. Take your total height divided by that stair rise number. This will almost always give you a long decimal number. Round to the nearest whole number – this will be the number of steps you will have in your staircase.
How do you calculate rise and run for stairs?
The vertical distance between the floors to be linked by the staircase is the principal determinant of the riser and tread dimensions. You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14).
How do you measure the length of a stringer?
How to Calculate Stair Stringer Length Measure the height from the surface where the stairs will start to the bottom surface that the stairs will connect to. Divide the height of the staircase in inches by the intended rise of each step, also in inches, to assist in determining the stair stringer length.
How long should my stair stringer be?
Stringers should always be cut from 2x12s. Notching smaller stock doesn’t leave enough wood to safely carry the loads of a stair. When ordering stringers, allow about 14 inches of stringer length for each step.
How do I calculate how many steps I need for stairs?
Divide the rise by 6 or 7 inches (15 or 18 cm) to find the total number of stairs. For larger stairs, divide by 6 and for smaller stairs, divide by 7. The total you get is how many stairs your future staircase will have so you can plan accordingly.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
How do you calculate stair landing?
The height of the landing is determined by where it is located along the stair run. In this design, since it is half way from the top level, it is 8 steps high (8 x height of each step (6 7/8) equals 55 inches). The horizontal positioning of the mid-level landing is determined by the number of treads on the stair run.
How far apart should stair stringers be?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
How long of a 2×12 do I need for stringers?
How to Use the EZ Stair Calculator. We suggest 10.5″ for 2×12 or 2 – 2×6 Treads. Treads may be cut to suit other widths. Either B or C is required.
How long should a 2×12 stringer be?
cut stringers. The two most common cut-stringer defects that I see are overspanning and overcutting. The minimum recommended size for a deck stair stringer is 2×12, which has a maximum recommended unsupported span of 6 feet.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has . 60 RET level.
How many steps are in 10 feet?
Length of Staircase for a 10 Foot Ceiling A staircase in a home with 10′ ceilings requires 17 steps. Stairs that have a tread depth of 11” will have a total length of 187”. Stairs with a tread depth of 10” will have a total length of 170”, which is the minimum length.
How many steps is 12 feet?
For example, suppose your height of ceiling is 12 feet high, generally you will need 20 stairs or steps to go up (12 × 12 ÷ 7 = 20). Formula for number of stairs or steps = total height × 12 ÷ 7 or height of staircase/ height of one riser.
How do I calculate my walking steps?
Photo: Pedometers can measure your steps because your body swings from side to side as you walk. Each swing counts as one step. Multiplying the number of “swings” by the average length of your steps tells you how far you’ve gone.
Can I use 2×8 for stair stringers?
You should attach 2×6 or 2×8 support framing under the rim flush to the bottom of the stringer. The stairs will hang here. Install a piece of blocking below the rim joist to extend the attachment surface for your stairs stringers. Use a level to mark the top step.
How tall is a 5 step stringer?
Stair Stringer-5 step Redwood (Common: 60 in. x 11 in.; Actual: 1.5 in. x 11 in. x 60 in.).
How many steps before a landing is required?
ADA Stair Landings – A landing must be at the top and bottom of each stairway. – A landing is required every 12′ of vertical stairway rise.
How many steps is 4 feet?
A four-foot high deck can have a range between 6 and 8 steps.
Does the landing count as a step?
Does the landing count as a step? Yes it does. It amazes me how many people like to argue this one. Remember that when counting stairs, you are counting how many times you have to lift your foot.
How high is a 2 step stringer?
Step stringers are cut for 2 In. x 12 In. treads, and have a 7 In. rise.
