Table of Contents
How do you calculate material for pinch pleat curtains?
Carolina Custom Draperies notes that you should multiply the total width by 2.5 and record the result. This allows for the proper amount of fullness for the pleated drapes. For example, if the total width is 84 inches, multiply 84 by 2.5 to get 210 inches, the calculated fabric width.
How do you measure for pleat curtains?
For pencil pleats on a track, measure the drop by starting from the top of the track, and for pencil pleats on a curtain pole, measure from the eye of the curtain rings (where you’ll be hooking your curtains into). Measure from either of these points down to your chosen end point and that’s your drop measurement.
How far apart should pinch pleats be?
Standard spacing is 5 pleats per 54” fabric width, however can be adjusted to accommodate different fullness levels.
How do you calculate pleats?
Tally the number of pleats that will be on the window curtain. For example, there can be six pleats. Divide the window length by the number of pleats, then calculate how big you’d like the pleat to be. Add another few inches for the fold of the pleat.
How is a pinch measured?
A pinch of an ingredient (usually a powdery or finely ground substance like salt , spices, or dried herbs) is the tiny bit your pick up between the tip of your index finger and thumb. If you were to measure a pinch, it would be between 1/16 and 1/8 of a teaspoon.
How much width of fabric do I need for pinch pleat curtains?
– A pinch pleat curtain requires more fabric to sew in the pleats as it gathers up tighter. As such you will require 2.5x the track width or 150% fullness. Standard window curtains you will use the guide above to decide on the amount of fabric.
How wide should pleated curtains be?
To achieve the pleated effect you notice at the top of most curtains, the curtains need to be wider than the track. The actual amount of gather depends on heading styles and personal preference, but as a general rule the width of your curtains should amount to double the width of your track.
What are pinch pleat curtains?
Pinch pleat curtains are a highly decorative heading, drawing together lots of fabric into a tightly gathered and stitched bunch at the top. The permanently sewn-in pleats make for a smart finish, with elegant folds flowing from top to bottom. You can have pinch pleat curtains with either a pole or a track.
How do you calculate pleat spacing?
Subtract the size of the RETURN and LEADING EDGE from the finished curtain width. Divide the result by (the number of pleats minus 1).
How wide should pleats be?
The extra fabric on the width is used to make the pleats. With 50% fullness, the pleat is usually about 3″ wide. With 100% fullness, the pleat is usually about 6″ wide. In both cases, there is typically 12″ from the center of each pleat to the center of the next pleat.
What is the difference between pencil pleat and pinch pleat curtains?
Pinch pleat is a decorative heading for curtains, suitable for all fabrics. Pinch pleats use more fabric and are fuller than pencil pleats. The pleats are hand-sewn in and permanently fixed for more luxurious, tailored look. This will allow us to gather your curtains to the correct width.
How do you make pinch pleat sheer curtains?
Although you can measure and stitch individual pleats across the upper edge of a sheer curtain panel, the easiest way to make pinch-pleated sheers is to sew on lightweight pleater tape, available at fabric and decorating stores. Use drapery pleat hooks in the pockets that are woven into the tape.
How do you measure pinch grip strength?
One pinch test is the three jaw chuck, where the thumb pinches in opposition against the index and long finger. The lateral pinch, or key where the thumb pinches against the radial side of the index finger as if holding a key. And the final test is a tip pinch where the thumb pinches opposite pad of the index finger.
How much is just a pinch measuring spoon?
This unique stainless steel measuring set is just that. A set of three measuring spoons come in a Dash – which is technically 1/8 teaspoon; a Pinch – which is 1/16 teaspoon; and a Smidgen – which is 1/32 teaspoon. The perfect gift for that chef in your family; guaranteed to be a kitchen favorite!.
How do I calculate how much fabric I need?
Figure out how much fabric you need with this formula: Width of fabric divided by width of one piece equals the number of pieces that fit into width (rounded down to the whole number). Total number of pieces divided by number of pieces that fit into width equals number of rows you need.
How do I calculate curtain material?
There’s a simple calculation to work out how much curtain fabric you need. First, multiply the track/pole width by your chosen fullness (eg. Pole width 150cm x 2.5 = 375). Next, divide that figure by the fabric width, which is typically 137cm (375 divided by 137 = 2.73).
How much material do I need calculator?
Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the total and divide by 27 (the amount of cubic feet in a yard). The final figure will be the estimated amount of cubic yards required.
