Table of Contents
To measure your countertops, start by measuring the length of all counter tops, base cabinets, and island. Also include the inches of back splash. Now measure the width of the counter tops and multiply the total length of the counter tops by the width in inches.
How do I figure out how much countertop I need?
multiply length times width in inches and divide it by 144. Please remember to include the backsplash in your calculation to get an accurate estimate.
How do you calculate square footage of a countertop?
Chapter Three: Calculate Total Countertop Square Footage To calculate the total square footage (after placing seams) you will need to follow this formula: “L” x “W” / 144 = s.f. (Length times width divided by 144 = square feet).
How many square feet of countertops are in an average kitchen?
The average measurement for a kitchen countertop is 30 square feet. However, the variation between kitchen designs is vast. There are kitchens with much smaller or significantly larger countertop measurements. The right size for your kitchen will depend on the floorplan and counterspace you want in your kitchen design.
How do you figure linear feet for countertops?
Measure the length of the countertop along its back edge (commonly, this is the edge that is against the wall or backsplash). Start at one end and measure each straight segment of countertop. Write down the length of each segment as you measure them.
How much counter space should a kitchen have?
For minimum space requirements, the National Kitchen and Bath Association recommends a countertop that is 158 inches wide and 24 inches deep. This results in a little more than 26 square feet of total countertop space. It’s important to keep in mind, however, that this is a general recommendation.
What is standard countertop depth?
While the standard kitchen countertop depth is 25 ½ inches, most kitchen island countertops can go up to 27 or 28 inches deep and over 30 inches deep if it comes with a breakfast bar. The island countertop depth depends on the availability of space.
What is the standard countertop size?
Countertop Width Standards Most homes are fitted with kitchen countertops that measure 25.5 inches in width (from the wall to the edge of the counter), with some measuring up to 28 inches. Standard measurements allow for a 1.5-inch overhang over 24-inch deep base cabinets.
How much does granite cost for a 10×10 kitchen?
Granite countertops will cost you around $40 to $60 per square foot, with the total price for installation and materials coming in between $2,000 to $4,500. Comparatively, marble costs around $75 to $250 per square foot, with the average cost around $75.
How long should a kitchen counter be?
The standard is 24 inches. But again, this can vary based on your size, appliance depths, and details of the backsplash and cabinetry.
How many linear feet of countertops are in an average kitchen?
The standard depth for countertops and cabinets is approximately 25 inches. This means that 30 square feet average will assume a total counter length of around 14 feet.
Is Granite sold by the linear foot?
The price is often calculated by linear foot. Although you might not be able to minimize the length of the edge that is polished, the edge itself will have an impact on the price. Standard edging will keep the cost to a minimum. These edges include straight or penciled edge, quarter round, or quarter beveled.
What is the difference between linear feet and square foot?
Linear Foot vs Square Foot: While a linear foot is a one-dimensional measurement, a square foot is a two-dimensional measurement. A square foot is the result of two linear measurements. For example, when you want to calculate the area of the room. You must look for the length and width of the room.
What is the kitchen triangle rule?
Developed in the early twentieth century, the working triangle—also known as “the kitchen triangle,” also known as “the golden triangle”—is a theory that states a kitchen’s three main work areas should form, you guessed it, a triangle. Specifically, the sink, the refrigerator, and the stove.
What is the best kitchen layout?
The galley kitchen is the most efficient layout for a narrow space. It consists of work spaces on two opposing walls with a single traffic lane between. Placing the range or cooktop on one side of the kitchen and the refrigerator and sink on the opposite wall allows for easy workflow.
Which kitchen layout is the most functional?
L-Shaped. The L-shaped kitchen is one of the most popular layouts because it’s super functional and can be adapted for almost any sized space. As the name implies, an L-shaped layout features cabinetry and appliances along two adjacent walls, creating an obvious triangle path between work zones.
How far do kitchen counters come out?
How far should a countertop overhang on the side? Generally, the standard overhang of a countertop is 1 to 1 ½ inches from the cabinet, while the exposed ends of a countertop will usually have a ½ inch overhang, and the ends that meet a wall don’t have any overhang at all to keep the fit flush to the wall.
Is counter-depth deeper than standard?
The distance from your backsplash to the front of your kitchen counters is one way to gauge your “counter-depth.” To fit within this space, counter-depth fridges are shallower than a standard-depth fridge, with a typical range of 23 to 27 inches deep.
