Table of Contents
Use a measuring tape to calculate the square footage of each room that will need base trim. Choose a starting place in the room — such as a corner or next to the door frame — and measure the length of the wall in inches. Write down each measurement and continue around the room until all walls are measured.
How do you measure for base molding?
Divide the total number of inches by 12 to convert from inches to linear feet. For example, if your wall measured 40 inches in length, and you are installing molding on the top and bottom, 40 x 2 = 80 inches. Divide 80 by 12 to get 6.66 linear feet.
What size nails should I use for baseboards?
As we discussed earlier with nail guns – the best baseboard nails are probably going to be 6d (2”) or 8d (2.5” for baseboard). These can easily accommodate 15 gauge or 16 gauge nails, giving you a long, durable nail for thick baseboards and studs.
How much do trim carpenters charge per linear foot?
Wood Trim Costs Item Unit Cost Line Cost Wood trim $4 per linear foot $2,000 Labor (carpenter) $70 per hour $1,680 Total Cost $7.36 per linear foot $3,680.
How do you measure for trim?
Measure along the wall and floor junction from the first corner to the first cut point. Record this measurement with an additional note detailing if the left and right sides of the trim are inside or outside angles. Also, note the degree of the angles.
How much should baseboard installation cost?
Baseboard Installation Cost Per Linear Foot Expect to pay between $5.70 and $8.95 per linear foot for baseboard installation. Contractors usually price installation by the linear foot, and these costs include materials and labor. However, you’ll likely pay at least $15 more if you need debris removal.
How do you measure baseboard trim angles?
Set the corner of the angle gauge into the inside corner or up against the outside corner of the surface you’re measuring. Open the gauge’s blades until they’re pressed firmly against the adjoining surfaces. Read the angle off the gauge. Lay a short piece of scrap baseboard on the floor, flat side down.
How do you measure corners for baseboards?
For inside corners, the long point of the miter is always at the back of the molding, against the wall, and against the miter saw fence. For inside corners, you measure to the long point of the miter and you cut to the long point of the miter.
What angle do you cut baseboard corners?
With inner mitered baseboard joints, each baseboard piece is cut at a 45-degree angle. When joined, the two pieces form a 90-degree angle that fits perfectly against the inside corner where two walls meet.
Do you nail baseboard to studs?
Base molding fits flush along the bottom of the wall and typically attaches to the wall studs and to the floor plate. The top nail should hit the stud and the bottom nail should either hit the stud or the floor plate, which is 1-1/2 inches higher than the subfloor.
Can you use 18 gauge nails for baseboards?
Yes, you can use an 18-gauge Brad Nailer for your baseboards. However, it doesn’t have the holding power compared to a 15 or 16-gauge nail. The 18GA nails work well for trims up to 1/2 inch. For baseboards thicker than 1/2 inch I recommend you go for 16 gauge nail gun.
What is the difference between a brad nail and a finish nail?
Most brad nails are made from a very thin 18-gauge wire. Finishing nails typically range from 16 to 10-gauges and are much more robust than brad nails. Finishing nails also come in a wider variety of lengths than most brad nails do; some can be upwards of 3” in length.
How much does it cost to paint trim and doors in a house?
Painting trim and doors costs $45 to $200 per side. Painting window trim and frames cost $25 to $150 each. Most painters charge $20 to $50 per hour in labor and recommend two coats of paint.
How much should I charge to trim a house?
Average Trim Costs The national average cost of installing trim in a house is $1,279, with a typical range between $604 and $1,994. The cost at the low end is $200, and the high-end cost is $5,200. Trim and molding are woodwork elements that embellish a home’s floors, walls and ceilings.
How much should I charge for trimming?
Depending on those factors, a typical price range for professional bush trimming is $50 – $75 per hour or $6 – $15 per bush.Equipment needed. EQUIPMENT NEEDED FOR DIY BUSH TRIMMING COST TOTAL $50.
How many linear feet are in a 12×12 room?
Multiply the length times the width of the room to get the room square footage. 12 ft x 12 in/ft (width of the room) = 144 in. So the total linear footage of the 1 x 12 boards is found by multiplying 5 (boards) by 6 (feet) which equals 30 linear feet.
How do I calculate baseboards for my house?
Add measurements together for each area — such as for the living room, dining room and so on — and divide the number by 12 to determine the linear square feet of each room, as base trim is typically sold in linear square feet.
How much does it cost to have a 12×12 room painted?
Painters charge $300 to $1,000 per room on average, depending on the size. The average cost to paint a 12×12 room is $400 to $950.Average Labor Cost To Paint A Room. Charge Average Cost Per Square Foot $1 – $3 Per Room $180 to $650 Per Hour $20 – $50.
Can I install baseboards myself?
Baseboard moulding is a simple way to add instant character to a room. While the installation of the baseboard trim itself isn’t hard, the cutting and measuring of the angles can be a bit tricky. A homeowner can easily learn how to install baseboards with this easy-to-follow project guide.
How do you find the angle of trim?
To calculate the proper miter angle for trim-work moldings, simply divide this angle reading by 2. In the example shown, the inside corner is 90.5 degrees—nearly square. The precise miter angle of your moldings should be 45.25 degrees.
