Table of Contents
Backset: A backset is the distance from the center of the cross bore, to the edge of the door. To determine the correct backset measurement for your door, you need to measure the distance from the edge of the door to the center of your cross bore.
What backset should I use?
The backset is the distance from the edge of the door to the center of the 2-1/8-inch bore hole. In the United States, there are two common backsets for residential door locks: 2 3/8 inches and 2 3/4 inches. Pack your locks with a 2-3/8-inch or 2-3/4-inch latch, depending on which backset you specify.
What does 45mm backset mean?
‘Backset’ is the distance from the front of the lock to the centre of the spindle as shown here. If you intend to use new locks or latches on an old door, replacing your old ones, you will need to make sure the new one fits into the hole in the door. To do this, measure the ‘backset’ distance of your old lock.
What size backset do I need?
You can work out the size of the lock by measuring the distance from the edge of the door to the centre of the door handle or knob. This measurement will give you the approximate size of the backset which will allow you to identify which size lock or latch you have.
What is the typical backset for residential exterior doors?
Backset: Measure from the edge to the center of the drilled knob area; 2.375-inches (2 3/8-inches) is the modern standard.
What is the most common backset?
Standard backsets are either a 2 3/8″ backset, or 2 3/4″ backset. The most common backset is 2 3/8″ but 2 3/4″ is also quite common – usually used on exterior doors. Sometimes it’s easier to measure from the edge of the door to the highest point on the bore hole.
What is backset on door latch?
The backset is the distance from the edge of the door to the spindle mechanism on the latch. Usually for a 63mm case measurement it will have a 44mm backset and for a 76mm case measurement will have a 65mm backset. The backset you choose is where your door knobs will sit on the door (where the spindle goes through).
How do I know what size door latch I need?
An easy way to choose which latch you need is to measure from the edge of your door to the centre of your door Stile. Choose the Backset which is closest to this measurement, and the handle will be as central as possible to the Stile on your door.
What is case and backset?
The backset measurement is the distance from the centre of the keyhole, to the leading edge of the lock. The most common sizes here are 44mm (on a 64mm / 2.5″ lock case), and 56mm (on a 76mm / 3″ lock case).
How do you measure a backset on a mortise lock?
You can measure the mortice locks by measuring the backset and the centre. It is also advised you measure the case width and height and the forend length and width. Backset – The backset is measured through measuring from the centre of the keyhole to the forend of the mortice lock.
What is a 65mm latch?
An internal door latch allows you to close a door and keep it in place without locking it. These sizes are the overall length of the latch, or the case. When measured to the spindle mechanism, the backset, then they translate as 44mm for the 65mm case and 57mm for the 76mm case.
Are front door locks standard size?
Are front door locks standard size? There are two primary measurements. The standard hole size for cylindrical locksets is 2 1/8″. Cylindrical is the most common type in residential settings.
How do you measure a backset hinge?
Hinge Backset The distance from the edge of the applied hinge leaf to the frame stop. This is a critical measurement and must be accurate within 1/32′′. The most common dimension is 5/16′′. The hinge backset on the door will be properly adjusted from this measurement (typical – 1/16′′) to ensure proper clearance.
What size is a deadbolt hole?
The deadbolt lock set will come with a template to help you with measurements. Be sure to use the correct size drill bits specified in the lock set instructions, though most standard deadbolts require a 2 1/8-inch hole saw for the lock bodies and a 1-inch spade bit for the sliding bolt assembly.
How do you measure an interior door handle?
Measure from the edge of the door to the centre of the door knob or handle. The industry standards are usually either 44mm / 57mm / 82mm / 107mm / 130mm. Ideally you will try and choose the backset measurement that sites the door handle in the middle of the door stile.
What is door cross bore?
Bore holes are the holes in the door that house your door hardware and allow it to be installed. The cross bore is the main hole drilled into the face of the door where the body of the lock (chassis) is installed.
